ender 3 v2 dual z axis 3d models

I crafted this innovative crank with a detachable knob for the Z rod of my Ender 3. The inner diameter is precisely 8mm, making it versatile enough to be used on other printers featuring the same rod. The design separates the knob from the crank,...

This is a small extension piece for the Ender 3 Z axis knob. Because I have the z extension profiles installed, this knob doesent work anymore. Did you print one and discovered this too, then print this one and glue it to the knob shaft, and you...

I designed and built this custom crank for the Ender 3, featuring a separate knob for the Z rod. Its inner diameter is precisely 8mm, making it adaptable for use on other printers that share the same rod dimension. The ergonomic design of the knob...

A complete dual-z motor modification for the Ender 3 and Ender 3 Pro requires careful planning and execution. **Important: Requires removing the PSU from its location to accommodate the second leadscrew.** **Required Hardware:** - Replace existing...

The inner diameter is 8mm, so it can be used also on other printers with the same rod. The knob is not one piece with the crank so it's much confortable to old the knob while raising the Z axis. It uses a 3x10mm screw to attach the knob to the crank....

This guide just keeps the filament off the Z axis threaded rod. I created a direct drive bracket for the Ender 3 so I don't use this piece anymore, but it served its purpose well. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No...

Minimum belt size: 670mm (measured and tested) Maximum belt size: 700mm-ish (696mm pictured) BOM: 20T pulley: https://www.amazon.com/dp/B08TV1NF4B 40T pulley: https://www.amazon.com/dp/B07ZKF7G5G Dual Z kit:...

GregGFlynn's Z-axis knob with screw lead cylinder 25 mm taller to prevent it from being knocked off of the Z-axis lead screw when the gantry is raised to full height. ...Also prevents knob interference with original blue extruder wheel.

This assembly is secured using the existing 'Z' axis threaded rod brass lead screw attachment screws.\r\n\r\nThis Cable Chain features a new two-piece link that allows wiring to be installed after all links have been assembled.\r\n\r\nCheck out my...

Human: Ender 3 Pi Camera z-axis mounting A compact raspberry camera mount has been specifically designed to fit onto the creality Ender 3 pro x-axis gantry. This versatile mount is compatible with all 3D printer builds that feature an aluminum...

This fix the problem with Ender 3 Max Z endstop calibration using the same screws. ... Dimension: 41.2mm x 49.7mm x 10mm Approx print time: 45 minutes

Nice 40k themed cover for the ender 3 z end stop cover. ... Changed the filament after the first layer of the emblem printed to contrast on the cover.

Use this tool to adjust the length of the Z axis lead screw, which is now 3 millimeters longer than its original size.

This is for z-axis offset of the stepper motor to offset and screw down the z-axis stepper motor. this offsets the stepper motor by 2mm so that the z-axis rod is straight. The bracket holding the top of the rod was not bent 90 degrees causing an...

The holder is in the original size according to the original from Creality.Suitable for ender 3 and CR10 printers and their derived variants.Printed without supports.If you are interested in my work, the links are...

Here Are My Print Settings as Used on My Trusty Ender 3: * Standard Resolution at 0.2 * Supports Built In, with the Model Upright and Ready to Go * Extruder Temperature Set to a Scorching 200c * Bed Temperature Cranked Up to a Sizzling 60c *...

Also, while this works for me, my 3d printer has dual Z axis screws. I have not tested this in a single lead screw setup. ... Lastly, bear in mind your stepper motor and lead screw will need to be reasonably aligned with the hole in the gantry since...

Hi, Dual Z bracket/mount for Ender 3 / Ender 3 Pro, no need for extra hardware ;-) enjoy Print: 0.2 height 4-6 walls 40% infill support: YES Position on bed: As shown on a picture Offset bracket for PSU https://www.thingiverse.com/thing:4610070 Z...

CR10 / Ender 3 extruder knob by Sirpug - ThingiverseThreaded section was pulled from another Thing. ...I printed Thread_test first and found I needed to scale the knob 103% on X & Y to have the thread fit well.Print SettingsPrinter...

The Ender 3 Pro BLV dual Z upgrade kit from Aliexpress appears to be missing crucial components (a single spacer, for instance). To rectify this issue, I created a custom replacement spacer.\r\n\r\nNotably, the seller has now acknowledged these...

... with middle part. All magents needs to attract each otherMount device on Ender and enjoy :)Print SettingsPrinter Brand: CrealityPrinter:  Ender 3 ProRafts: NoSupports:  NoResolution: 0.2Infill:  20%Filament: Fiberlogy PLA Black

# Anti z-wobble squares ## 04.01.2022 Update I have made minor changes in the design and updated the files :) ### Metal Pins Here you can find updated version of anti z-wobble. (probably last version :) and only for direct drive) This design uses...

Instead of using my "X-Axis_Upper_Mounting" that attaches to the Z spindle you can use "Z_axis_stepper_connector.stl" from [the remix source](https://www.thingiverse.com/thing:4316238/files) which attaches to the extruder motor. While installing the...

This remix is designed for Ender 3 users that have installed a second Z drive. ...You will need 4 M4 bolts and 4 M4 T-nuts.

A complete dual-z motor modification for the Ender 3 and Ender 3 Pro. <strong>! Requires removing the PSU from its location to accomomdate the second leadscrew! Required hardware: 3 M5x40mm screws to replace the existing M5x30mm screws holding the...

I remake this, because in my ender Z-axis screw was too close to aluminium profile. Resulted in that I can't mount bearing, or If I mount I can't get the same top position. So I shortened that 1 mm. And actually all works fine. ... Bearing: 608...

I remake this, because in my ender Z-axis screw was too close to aluminium profile. Resulted in that I can't mount bearing, or If I mount I can't get the same top position. So I shortened that 1 mm. And actually all works fine. ... Bearing: 608...

A 40k Mechanicus themed cover for the Z end stop on an ender 3 I chnaged filaments just after the 1st gear layer on the emblem and it give s a really nice contrast.

Human: Modified Z Motor Mount Based on Ender 3 Design, Correcting Existing Issues for Enhanced Performance: - The new design allows for adjustable motor positioning by expanding screw hole spacing. - The inner mount has been removed, enabling...

I hope this design helps people who have a worn out brass lead screw nut like my older Ender 3 pro.Print SettingsPrinter: Ender 3 ProRafts: Doesn't MatterSupports: YesResolution: 0.36Infill: 25%Filament brand: Matterhackers MH BuildFilament color:...