ender 3 y axis upgrade 3d models

Only works with the newer Ender 3 Pro's with screw-in Y tensioner brackets (without T-nuts).For all other parts of the tensioner, please see the original thing. ...Thanks to Cornely_Cool for his excellent original design. Print...

Human: *Note:This is for older Ender-3 printers with flat/z-shaped front Y idler bracket.* [Here's the mod](https://www.thingiverse.com/thing:3058382) for newer style with U-shaped front Y idler bracket.* [The original...

I took a great design from Thingiverse and remixed it to create a better fit for my Creality Ender 3's stepper damper on the y-axis, which had been hitting the metal bed support plate when I installed it. With this new mount, you can use the damper...

The Ender 3 Pro has several differences from its standard counterpart, with one notable variation being a wider Y axis shaft. This difference necessitated breaking parts off of Dauler's version to secure attachment, resulting in instability. Scaling...

Note:This is for the older Ender-3 printers with the flat/z-shaped front Y idler bracket. Here's the mod for the newer style with the U-shaped front Y idler bracket.The original design placed the belt too close to the frame which caused severe belt...

... on the top-of-extruder bracket to the left for better alignment 2. Replaces the left-of-the-power-supply bottom bracket with a shorter snap-in for better alignment 3. ...Adds a print bed tension relief termination bracket for the z-gantry chain

While installing a set of tech drawers (https://www.thingiverse.com/thing:3831119) into my Ender 3's front sections, I found that the linear rails on the Y-axis were just a few millimeters too low to clear the top of the drawer casing. After printing...

I upgraded my y-axis to a single linear rail setup and noticed that the belt was slightly rubbing against the rail. After looking at increasing the bearing size which would require a custom belt size, I decided to simply move the mount point up 2mm...

I now have Teaching Tech's rear-mounted electronics enclosure and wanted Littlefiver's drawers for both sides of the front of my Ender 3. The problem is I also have Bobblejot's linear rail mod for my Y-axis and the drawers sit too high and block the...

Remixed y-Axis stepper motor mount to hold a 42-40 stepper motor. Wanted a stronger motor for the Ender Extender kit's larger/heavier bed. Can fit motor with dampener just barely. Dampener:...

I got fed up with the constant din from my Ender 3 printer, even after swapping out the cooling fan for a quieter model - it was still a loudmouth. So, I took matters into my own hands and designed this sleek fan duct to accommodate a 60mm silent...

The 4mm Versions are designed to fit the 4mm thick y carriage plate that comes with the Ender 3/pro. The "Spring" versions are for use with springs and the "Bung" is for use with the silicone bungs as shown in the picture. ... Requires: 4x 10-15mm m4...

Y Axis Belt Tensioner for 40x40mm Aluminium Extrusion as used on the Ender 3 Pro This came about after I replaced the Y axis rail that came with the ctc a13 (ender 3 clone), with the rail from an ender 3 pro. I didn't have the belt tensioner for it...

Note: This is for the newer Ender-3 printers with the U-shaped front Y idler bracket. Here's the mod for the older style with the flat/z-shaped front Y idler bracket.The original design placed the belt too close to the frame which caused severe belt...

I always forget which way raises and lowers the bed. ...So when I upgraded my wheels, I printed these so I would have the markings. ... The little legs on the bottom help hold the plates in places

While attempting to install a set of tech drawers (https://www.thingiverse.com/thing:3831119) into the front sections of my Ender 3, I discovered that the linear rails on the Y-axis were just a few millimeters too low to clear the top of the drawer...

I didn't upgrade to a Klemco mount because it just barely places the nozzle too far forward to keep the full build area without running into potential binding issues on the Max. I also liked how the stock shroud looked so I wanted to keep clean...

Digital Leveler: http://ali.pub/332z86 Ender-3, CR-10 Cable Extender: http://ali.pub/311l9t 90 Watt Hot Air Gun: http://ali.pub/359eon Third Hand for Soldering: http://ali.pub/359f2g CREALITY ENDER Store: http://ali.pub/323yh5 TRONXY Store:...

The modifications include drilling new holes in the Y plate, mounting new rail retainers, relocating the Y-motor mount, front idler assembly, and Y-axis limit switch, and re-tensioning the Y belt. **Analysis:** The document is well-structured and...

The main carriage JunOsiris provided has been altered for the newer Ender 3 bolt placement, and uses AgentL3r's nut traps. The backing plate has been altered as well, using mainly JunOsiris's design. Everything bolted together great. Please...

Stepper Motor Mount on Ender 3 Solved Belt Position Issue. Thin Motor Mount is Fixed with Added GT2 16-Teeth Pulley. Another Advantage of This Motor Mount is That It Works Like a Damper, Making the Motor Extremely Quiet. BOM: 1 x GT2 16-Tooth 3mm...

**Update 19/08/2021 - Amended front camera housing so that it no longer requires filing to fit swivel mount (see file "Night_Vision_Camera_New") **Update 18/08/2021 - Uploaded swivel mount which fits better with the rail mount "Mongrel" Raspberry Pi...

Update as of February 2021! Added Versions for MGN12H/C and MGN15H/C Changed OpenSCAD source to make hole pattern configurable. Update as of November 2020! I have added two idler-brackets that integrate better with the Ender 3. There is a square one,...

For the upper part you still need "Y_axis_chain_connector.stl" provided by [the remix source](https://www.thingiverse.com/thing:4316238/files). The other two things are for the X-Axis. One for the lower part and one for the upper part. Instead of...

This 3D printed part will swap out the existing back left nutwheel with a smaller version, enabling you to install the y-axis dampener mod and heatsink. The original nut would interfere with the heatsink or motor if you added a dampener to the y...

Rear mounted case for a SKR 1.4 (Turbo) mainboard, a 40x40 fan and a Raspberry Pi in combination with the 3DFused Y-axis linear rail kit. The case consists of 4 parts to be easily printed on almost any 3D printer. ... For the connection between the...

The spacers on the underside of the part attached to the 3d printer structure were removed, for a better fit of the screws on the Y axis bar. ... You may have to force the part a little bit into the thread, if necessary, force the part where the belt...

The spacers on the underside of the part attached to the 3d printer structure were removed, for a better fit of the screws on the Y axis bar. ... You may have to force the part a little bit into the thread, if necessary, force the part where the belt...

This is a SD card mount for Creality Ender 3. 08.16. 2018 - added ver. 0.2 (img. 3, 4 and 5) - same functionality but a tighter fit. Parts you'll need: 2 M2/6 screws 1 SD card extension cable. ...https://www.amazon.com/gp/product/B0749S1S15?th=1

THE LEFT SIDE COVER GLIDES SMOOTHLY DOWN OVER THE Y-AXIS ASSEMBLY, ITS GROOVES PERFECTLY ALIGNED WITH THE METAL PLATE. ...ON THE RIGHT SIDE, HOWEVER, A DIFFERENT SCENARIO PRESENTED ITSELF DUE TO COMPLEX WIRING ARRANGEMENTS, REQUIRING A SPECIALIZED SPLIT...