fantasy dagger 3d models

now you can the stands/feet print without support or if you want the texture of the powder-coated pei sheet you can print it on its side without support.Release Candidate 1.5 - 15 January 2021Updated some sections to the model so it's stronger when...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

 For me, it pressed in very tightly; if in doubt, glue it in.To mount the holder, I stuck this adhesive mount onto the back, and used it to replace the jaws of an older model of this suction base.  The adhesive mount’s socket is smaller...

If you look at the print of the base (or the model of the legs) you will see there is a round hole with three slots surrounding it. These slots fit a specialized washer that is used in the vise to keep the base from rotating when it has been...

The sourced parts needed are the same than for a MyRCCar OBTS Chassis, so you can use them in all models by now. This means that you can reuse existing parts from other projects, making it easier and more cost-effective to build this chassis. If i...

is ASVFSVF14K203 [US] [CA].----------------PrintingThe “ALL.stl” file prints the entire set of models you'd need to assemble ONE power plug housing. Separate STL file for each of the part is also provided for your...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

Helicopter Collective Controller Work in progress. 6/17/20 Added File Added collective_open v4.f3d (An assembled model of all the parts.) You can alternatively use my Russian style grip located here:...

This is a well known test model with many remixes.However, I have not seen anyone with automatic temp range.Existing temp tower is “semi-automatic”, they set temperature to preset levels with custom g-code in “before layer change”This print set...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: The Sightless Seer] Known among many of his comrades as Byrè-Myn Fyreth, One-Man Army. Zyril is infamous for his single hold out in the town of Tara when...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

I made this trap to prevent those pests from killing the bees in my garden if they ever come close. I collected information, examined several models, made by individuals and professionals. This is my version. If you feel it is inspired by something...

If you are looking for more, check out our premium projects: https://codeandmake.com/premium OpenSCAD Customizer Options You can customize everything from the size of your cards, to the number of decks it will hold and you can even create a...

... that is about 1/4"/5mm in the front center due to the belt tensioning clip bumping into the blower. Unless you like that kind of centrifugal blower fan on belt tensioning clip action, I recommend not to drag the models dead center to the front.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

For other sizes of tube or different grid arrangements, you can use the Thingiverse Customizer to remix your own version (the recommended way, so others can benefit from your work) or download the model and use the OpenSCAD Customizer (available in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

This is a procedure to prevent the bottom part of the model from collapsing. (a.k.a. elephant foot)  7. Nothing is attached to the top of the Z-axis frame yet. Do...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

... - The +1mm fan duct is for use with longer non-standard m6 nozzles - Use the following commands to use with stock Prusa firmware: M92 E690, M500 - You may need to adjust the extruder motor current using M907 but that depends on your motor model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Keep doing it until you get a reliable contact. Multi-color printing For printing in multiple colors, you need to slice the model and save it as normal gcode. Then, you have to insert the M600 command. You can do this manually by opening the gcode,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...