flashforge dreamer 3d models

https://3dwarehouse.sketchup.com/user.html?id=0322118571106718978163948 This model was created utilizing his 3D file of a myosin II mini filament inside of Sketchup Print Settings Printer: Flashforge 3D Creator Pro Rafts: Yes Supports: Yes...

This is a replacement carriage for the Flashforge Creator Pro. This is still a work in progress! But it's currently being used in my machine! This is a Single Extruder Modification; it may or may not work with the factory firmware. It's working in...

- Examples in the photos were printed in PLA at 0.18 mm layer height, using a 0.4 mm nozzle on a Flashforge Adventurer 3. To assemble: - If your Retromax came in a case with a front, remove it very carefully so as not to damage the LEDs or...

Blue: (Bumat PLA- Transparent Blue) Fun fact, this filament came with my Flashforge seven years ago and still prints fine without being brittle. I keep my filaments in individual zip lock freezer bags with some desiccant. water .. White:...

I only have experience with my Flashforge Finder, so I can't give you really good advice on printer settings. But with my printer and Simplify3D, I ran about 15-20% infill (more on the lower parts for rigidity) and on the medium setting. I also run...

Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.1 mm Infill: 100% Notes: 100% infill will result in a heavier and longer-lasting spinner. For the same reason, a dense filament like PETG...

Material and Time Estimates The estimated amount of filament and time to print on my Flashforge Creator Pro using the draft profile are listed below. The time will be different for your printer and settings. I printed my 15% model using my usual...

Print Settings Printer: FlashForge Creator X Rafts: Doesn't Matter Supports: No Resolution: 0.2 mm Infill: 10% Notes: See notes below for helpful printing and assembly instructions Building the Model Colors (there are no multiple printed pieces)...

I used 4 short m1.4 screws (one screw on each end of each hinge which holds them together nicely Print Settings Printer Brand: FlashForge Printer: Adventurer 5M Pro Rafts: No Supports: No Resolution: .15 to .25 for the hinges as they are SMALL...

Makerbot/Flashforge) This remix splits the model into 3 pieces and adds joints. This design doesn't change overall dimensions of the visor, so the plastic sheet can be attached exactly same way as the original. Models (North America 6-hole version)...

Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Yes Resolution: 0.1 Infill: 15% Filament: 3D Hero ABS Black Notes: Printed at 235 degrees on a 105 degree glass bed with brim. Post-Printing ============= Attaching the...

It is designed to print on smaller volume printers such as the MakerBot or the FlashForge Creator. This also provides the opportunity to print in multiple colors for a more attractive case. The custom knobs are also available for purchase on...

                                               ...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                     

Whirligig in action: https://www.youtube.com/watch?v=OIgfxB2ZQw0 Print Settings Printer: FlashForge Creator pro Rafts: No Supports: Yes Resolution: .2mm Infill: 15% Notes: Print the billboard support at 100%. It needs the extra strength. Then add...

Print Settings: Printer: Flashforge 3D Creator Pro Resolution: .27 Infill: 15% Notes: A 15% infill should be sufficient for the bird print, but it can be increased if necessary. Post-Printing: Finished prints by user mled90 showcase the original...

The sample 3D STL file included is borrowed from user timelapse21 on Thingiverse: https://www.thingiverse.com/thing:1378432 Print Settings: Printer: Flashforge 3D Creator Pro Rafts: Yes Supports: Yes Resolution: .27 Infill: %15 Notes: It's...

Print instructionsPrint Settings Printer: FlashForge Creator X Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 10% Notes: See notes below for helpful printing and assembly instructions Building the model Colors (there are no multiple...

I also chopped off the front of the bracket to a total length of 198mm so it will narrowly fit on my FlashForge Creator Pro. This is my ABS workhorse and I wanted to use this material due to the added strength and durability of surviving banging...

I printed this adapter using a FlashForge Creator Pro printer with the following settings: no rafts, supports enabled, and a resolution of 0.3 mm. When printing in ABS, I found that maintaining adhesion was a challenge due to the summer heat...

Print Settings Printer: Flashforge Creator Pro Rafts: No Supports: No Resolution: 0.2 LH / 0.4 Nozzle Infill: 35-50% Notes: If you can spare the time, use a slightly higher resolution but 0.2mm Layer Height is fine. Post-Printing Fit Top Block and...

These files are similar to ones originally made for the FlashForge Creator Pro but have modified nozzle positions because the QIDI Tech 1 has the center levelling screw at the rear instead of the front. Carelen notified me about this difference. The...

The exhaust hole (the small one remaining when using the exhaust cap) is specifically designed for the MakerBot Replicator 2X (and possibly clones such as the FlashForge Creator Pro) that have enclosures but have holes in the bottom inner corners. ...

Print Settings: Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 10 Notes: Here are my recommendations for a good solid print. Headphone rest (Choose one): Regular: Print it on its side with supports...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                      

But once its going it prints pretty well. Hatchbox White - PLA Solutech Natural Clear - PLA Print instructionsPrinter: FlashForge Creator Pro Rafts: No Supports: No Resolution: .2 Infill: 20% Notes: Printed with skirt / brim and 10% speed on first...

I use a Flashforge Finder Lite, one of the cheapest, so you should be good to go. All parts have been positioned for you. Support is needed for all of them. Because these are not detailed models, I've been successful in printing these at standard...

This is the maximum height I can print with my FlashForge Creator Pro with glass bed. There are 3 cams that have to be placed on the quarter inch rod drive shaft such that they rest directly under the push rods from the reindeer and sleigh. Each...

Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2mm Infill: 100% (clamp) or 0% (taped) Filament: Velleman PLA, PETG Glow-in-the-dark, white Notes: For the 'clamp' model, PLA is...

Blue: (Bumat PLA- Transparent Blue) Fun fact, this filament came with my Flashforge seven years ago and still prints fine without being brittle. I keep my filaments in individual zip lock freezer bags with some desiccant. water .. White:...