goodluckbuy 3d models
43 3d models found related to goodluckbuy.thingiverse
This is a upper plate for the cheap goodluckbuy 2-axis gimbal to mount it with two of my Tarot mounting brackets. ...Print Settings Printer Brand: RepRap ...
thingiverse
I printed this bracket for mounting my cheap goodluckbuy 2-axis gimbal on my tarot 650 and 680 copters. ...Print Settings Printer Brand: RepRap ...
thingiverse
This is a simple adapter to fit Goodluckbuy 3-axis Storm32 gimbal on TBS Discovery frame. Didn't test it in flight, but I think that the yaw motor might be seen in camera when moving forward with high speed. If you find a good solution please publish...
thingiverse
If you have the cheap 2-axis gimbal from goodluckbuy and want to mount it forward-facing on your quad/tri/hex/octo/motorcycle/racing boat, then you've come to the right place. Instructions This plate...
thingiverse
http://www.thingiverse.com/thing:363690 27/6/2014: Added dampener plate (body plate) for Phantom 2 Vision Added dampener plate (body plate) for FC40 / Phantom 1 Instructions To complete this build, you will also need: 1x GoodLuckBuy controller board...
thingiverse
Remixed to change the hole spacing 2mm wider to mount to the GLB aluminum plate.
thingiverse
Fits the following Ublox NEO-M8N: http://www.goodluckbuy.com/ublox-neo-m8n-flight-controller-gps-with-protective-shell-for-pix-px4-pixhawk.html
thingiverse
I designed this stand for CNC aluminum alloy GPS shielding case which is sold by Goodluckbuy.http://www.goodluckbuy.com/cnc-aluminum-alloy-gps-shielding-case-protector-anti-interference-dji-naza-compatible.html Print Settings Printer: Makeblock...
thingiverse
Designed to use the small rubber ball dampers (3 hardness ratings available to suit weight of flight controller) from goodluckbuy, this was designed to be as small as possible for tight spaces.
thingiverse
This is a bottom frame and motor support for the CJMCU quadcopter that is available at Goodluckbuy.com http://www.goodluckbuy.com/micro-quadcopter-flight-driver-controller-9dof-9-axis-altitude-sensor-stm32f103.html The frame only weights 3 gram. ...Best...
thingiverse
Yaw Motor http://www.banggood.com/RCTimer-BGM2804-100T-Brushless-Gimbal-Motor-Hollow-Shaft-p-951199.html Roll/Pitch Motor http://www.goodluckbuy.com/brushless-gimbal-motor-2208-kv80-for-gopro-3-camera-mount-gimbal-black.html Storm32 BGC...
thingiverse
This is to mount the Mobius camera on the Goodluckbuy or eBay Simple Brushless Gimbal which is meant for the GoPro cameras. The adaptor allows for the Mobius to be mounted with adjustment so that the weight is correct for the gimbal. ...It mimics the...
thingiverse
... tight fit when printed with brittle material*** Simple mount for canon a2300 facing downwards. ...Mounting holes for gimbal suspender hooks. http://www.goodluckbuy.com/xa650-x650-landing-skid-mount-fpv-gopro-gimbal-suspender-mounting-hook-8mm-2pcs.html
thingiverse
This motor mount was created to fit those motors :http://goodluckbuy.com/a2208-17-1000kv-outrunner-brushless-motor-for-rc-helicopter-multicopter-4-pack.html, the holes at the bottom have been turn by 180 degres to match the a2208 motors.
thingiverse
The rubber anti-vibration balls are from GoodLuckBuy (http://www.goodluckbuy.com/10mm-high-elastic-rubber-ball-dual-head-anti-vibration-for-ptz-5-pack.html) The camera saddle is screwed directly to the 4 point servo arm. there's a hole to access the...
cults3d
The rubber anti-vibration balls are from GoodLuckBuy (http://www.goodluckbuy.com/10mm-high-elastic-rubber-ball-dual-head-anti-vibration-for-ptz-5-pack.html) The camera saddle is screwed directly to the 4 point servo arm. there's a hole to access the...
thingiverse
Remix from http://www.thingiverse.com/thing:415101 FPV Camerahttp://www.goodluckbuy.com/1-3-sony-hq1-super-had-ccd-camera-lens-module-set-700tvl-support-osd-for-fpv.html Fixed with to cable ties. The Camera Extension fit into the three slots of...
thingiverse
This is a pressure fit housing for the BGC V3.5 controller that is sold on Banggood and goodluckbuy. *Please note this is the side mounting version not the rear mounting version. View the picture to see if your wires connect at the same...
thingiverse
http://www.goodluckbuy.com/dji-phantom-brushless-gimbal-camera-mount-w-motor-and-controller-for-gopro3-fpv-aerial-photography.html It will also move the Gimbal/camera forward a little to avoid the signal/power outputs and also avoid getting the legs...
thingiverse
Bobbin spacing is for http://www.goodluckbuy.com/3-axis-brushless-gimbal-camera-mount-with-32bit-storm32-controller-for-gopro-3-4-fpv-black.html FC mount is for any 36x36mm fc. Used hs1178 as fpv cam. Booms are OD 12mm, ID 10mm carbon fibre tubes in...
thingiverse
I just wanted to put a goodluckbuy modified gimbal in front of my xugong... A bit heavy, but it works flawlessly. this plate replaces the original front plate, and you just need 2x M3x40 screws to go all the way throught the face plate, and lock...
thingiverse
I got mine from http://www.goodluckbuy.com/pixhawk-rgb-usb-module-external-led-indicator-for-pix-flight-controller.html used an m3 screw to secure the the triangle piece to the door and hot glue to secure the led cover to the triangle piece. Not...
thingiverse
This is a gimbal mounting plate to mount a Goodluckbuy 2-axis camera gimbal to my Cheerson CX-20 (Quanum Nova) quadcopter. The 3D-printed part will replace the top metal plate of the gimbal. The objective was to mount the camera as far back as...
myminifactory
I got mine from http://www.goodluckbuy.com/pixhawk-rgb-usb-module-external-led-indicator-for-pix-flight-controller.html used an m3 screw to secure the the triangle piece to the door and hot glue to secure the led cover to the triangle piece. Not...
thingiverse
... precise distance between the mounting holes, IMU size etc... Instructions Requires: 2x M3x16 screws (longer for SJ4000) 2x M3 nuts Goodluckbuy style IMU (20.1x16.5mm, distance between holes: 15mm) Distance between slits (center to center) is 8.5mm.
thingiverse
... Please note that these files are released under a non commercial creative commons licence. This licence has been ported to China, so that if you are from Goodluckbuy.com or Taobao and want to copy this, I have legal grounds to persue you.
thingiverse
http://www.goodluckbuy.com/2-axis-gopro-2-3-brushless-camera-mount-gimbal-with-motor-and-controller-for-gopro3-aerial-photography-.html ) and you own an Arducopter Hexacopter...
thingiverse
Gimbal: www.goodluckbuy.com/3-axis-brushless-gimbal-camera-mount-with-32bit-storm32-controller-for-gopro-3-4-fpv-black.html Phone mount: http://www.ebay.com/itm/like/302479122452 joystick:...
thingiverse
I used about 80%-90% infill to be stiff enough Parts you need 1x Controller board: http://www.banggood.com/Storm32BGC-32-bit-Brushless-Gimbal-Control-Board-With-MPU6050-Sensor-IMU-Anti-interference-Module-p-996912.html?p=OF26119123132014119R 3x...
thingiverse
The voltage regulator that I used came with another piece of kit that I had lying around, but it seems to be [this one](http://www.goodluckbuy.com/dc-dc-power-module-regulator-5v-output-voltage-buck-module-converter-dm02-5.html). ... --- [OnShape...