goth modeling

It will be a lot easier for me to fix a problem than for you to re-model a part. Designing my first blaster has generally been a fun experience, a bit more difficult than I thought it would be though! Stock mounts and magwells were the most...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0 custom_bottom_port_length = 40...

The battery negative is connected straight to the Anderson PowerPole negative and the radio negative.The model includes a plate to put on top of the batteries to ensure nothing gets in and shorts them out.To make the antenna fit inside the box with...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Required hardwareRaspberry Pi Pico (RP2040) microcontroller boardUSB cable (as it has to be cut and soldered a USB 2.0 is preferred, because it only has 4 wires)4x Cherry MX key switches or other with similar size4x Keycaps (or print your own)4x M2x6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

Carefully tipping the rocket body to allow the superglue to dry and smooth out.Repeat this process until all 3 fins are in place.  Producing the launch guide When launching a model rocket from a standard launch platform a 3.5mm guide...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

See overview here for model comparisons: https://makezine.com/2014/11/22/review-airwolf-hd-hdx-and-hd2x-3d-printer/ The Airwolf APEX Software has pre compiled firmware included for all the HD series but the m500 command is disabled. The public...

License ------- The "Bitten Doughnut" models (.stl) are licensed under the [CC BY](https://creativecommons.org/licenses/by/4.0/) license by [Code and Make](https://codeandmake.com/). The "Bitten Doughnut" code (.scad) is licensed under [The MIT...

Included is a list of hardware & electronics that can be used, a number of custom designed parts, and links to other Thingiverse parts to aid in completing this as a fully functioning RC model. All parts were printed in PLA, with 25% infill, and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Have a look at this Prusa blog post. Note that the parts will only come into contact with clean water so I just used mine as printed. You might want to sterilize the printed parts and the float valve when cleaning your sprouter (eg, using a...

I have no model or figure of Buffaloman in a camo tank top. The bazooka is actually pointing backwards to simply be held resting on his shoulder. I scaled it to 40% and positioned it to be resting between two shoulder spikes with the hand grip...

See photos. This is my take on a Morse Code sideswiper key, (also called cootie keys.) Unlike the traditional telegraph key which uses an up-and-down motion, the sideswiper makes contact on either side of a flexible arm, making for much less hand and...

current problems: - comments and filenames are mostly in German language - some of the mounting holes in the pcb are not at the exact right place - the pcb was designed with easyEDA and not with an open source program like KiCAD, which is compatible...

Don't go bananas with the size of your 50mm fan - there isn't a lot of room to play with; I'd suggest a slimline model for safety. - Print out your Bleh5, any (non-wobbly) material will do. - Note the picture above and glue it to your assembled...

In many channels for the promotion of new electric bikes, people who access the channels, like me, are also excited about the new models of electric bikes, almost always great projects. However, many were frustrated because they would like to have...

One uses a buck converter that is very difficult to find at the moment, so this model is not uploaded. This is the one I use. The other one has a larger area inside so you can fit other converters, should you want to. You can ignore the converter and...

(The toothbrush still shouldn't fall out, but a hole any larger and it might...)(I also use a print of the original model as a holder for fine detail paintbrushes, so a hole in the bottom of that one would be rather pointless.)Enjoy!Print...

I discovered this innovative concept on Chep's/Elproducts YouTube channel, where he credits OneBadMarine for originating the idea.\r\nhttps://www.youtube.com/watch?v=Fb4XMbZ0iA4&feature=youtu.be\r\n\r\nInitially, I encountered difficulties slicing...

I set out to model Mjolnir in my own way with an ode to some of the things I really like about the MCU version. My main caveat was that I wanted to use as little support and post-processing as necessary.Printing and Assembly Tips:The head has been...

Supports: Yes (if using Cura we recommend using the Tree supports option and adding a 'Brim' to help the Tree supports adhere to your print bed) Rafts: Doesn't matter Links View on Cults View on Thingiverse License The "Personalised Voronoi Sphere...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

Here is a 1:1 scale model of the first rover called Sojourner =) The frame is assembled from a 20x20 mm structural aluminum profile. All parts are printed with PLA plastic, everything fits on a standard 200x200 mm table, but it is advisable to use...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The handle houses the controller with its user interface and no base unit is required.All that is missing to be the perfect soldering solution for workbench and mobile needs is a stand and a housing.Introducing TStationThe TStation is a case for the...

If you do this, use the "Pusher Extd" model. To modify the solenoid: 1. Remove plunger. Remove about 3mm of the black base and sand flush with the metal slug. Sand the black base to make it slightly thinner if you want to add an additional spring...

the vanilla singleplate model), though the pulleys included here are a bit different from those. Re-cut bolt/nut holes in the idler pulley holder and thumb wheel to accept M5 hex bolts (because those are all I have with hex heads :-P ) Added an M5...