gpu 3d model

My printer is a I3 Pro Dual Extruder, so I know for sure it fits that model and probably all of the I3s that were made with that frame. Update 1/22/18: I added a new mounting plate that moves the stepper motor forward. This allows the X carriage to...

&nbsp;After getting the other nosecone to work I found out that the original Sprint used a BNC-50X and I had modeled off the BNC-50Y. &nbsp;So for ‘authenticity sake’ I've added a BNC-50X version of both the stock and Astrocam nosecones.</p><figure...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

I recommend 3 loops since this is quite a small model. Otherwise not enough PETG is dumped before the start of the parts</p><p>Print bed recommendation: Powder coated steel sheet with glue stick. I usually just put a 5cm to 10cm light line on the...

... satellite. The team’s website is http://csdc.uvic.ca/ Note that I did not create the Diamagnetic Payload Assembly, this was created by A.G.O. Environmental Electronics Ltd. The magnetorquers are not in the model, as they are still in development.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

You can find the newer version here: Phone Mount for Van Moof S2/S3 V2.0====================================================================&nbsp;Rotating Phone Mount for the Van Moof S2/S3 electric bike.Mounts to the handlebar using 3 cable-ties,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Videos of it in Action https://youtu.be/r5L5heNE0SIhttps://youtu.be/OzILwtWoT2M What Else Some other great models to add https://www.thingiverse.com/thing:3090510 BMG bowden mount for 3030 extrusions Updates 2020 Jan 22 * Better fit for fan magnets...

I know, it's specifically for the Ender 3 & I am using a Mega Zero, so no surprise that it does not work but I have no idea why before now I didn't see the problem when using these Ender 3 designed mounts with my Mega Zero, even if I'd mirrored the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

... diameter of the hose end 30mm away from the tip (the wider part) This will give me the diameter and taper needed to revolve a new part for anyone who wants one. Please let me know what make/model it goes to and I'll add it if I am able. ...

The first number at the end of each model's filename is the size of the PVC post that the adapter is intended to go on top of, the second number is the size of the PVC pipe that the finial would normally go on. I have a collection of Halloween things...

MINEY’, etc., up to a maximum of MO".(On the MINI model, stop at “MINEY’. There is no MO’)</li><li>You may use each finger more than once (a unique feature of your IAEA MINI<br>Calculator).</li></ul><h4>Subtraction</h4><ul><li>Reverse of instructions...

Add one if you have adhesion problems.Dimensions and Part NumberingYou find models for many combinations of heights and depths. The heights are in the range 35mm – 100mm and the depths are in the range 80mm – 190mm.</p><p>These numbers are included...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Ranger from Nan Thalias. Ervion was sent as part of an Elven diplomat’s escort, alongside his father which was attacked by a retinue of goblins and bandits near the County...

The bearing is model 6000. I would get one that is sealed to keep the saw-dust out. You may need to do some small scaling with your slicer to get the sizes correct. For my printer the bearing easily presses into the Depth stop, and the collar...

Tools Hex wrench 2mm and Mmm...

 The fan mounting holes are sized to accommodate a Brass Heat-set insert size M3x4mm.  The holes are not threaded and too large to accommodate an M3 screw itself.   Upgrading the Raise3d Pro2 with a Copperhead  Note: Both Hotends must be replaced...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

If you like & use my models please consider supporting my efforts with the button below. Thank you!…Please be sure to hit like & post a make, I'd love to see your prints!The Vortex series grows with Gemini! Print faster with crisper cleaner looking...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

I need thosethree measurements from that photo: Front standoff spacing, back standoff spacing, and front-to-back spacing.I've already helped several people from across the globe and I've been updating this document with the new models as I go.Post...

and Pause Layer = 2. How I Designed This Print on Window Screen This model was designed to have the printer paused at ~1mm to have the screen inserted. I made sure I made the frame thick enough to allow for multiple layers to be printed on each side...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside. These are for sink and drain plumbing only,...

I was unable to find a free CAD model of the G5 on the internet. assistant Greetings, I started this endeavor to obtain dimensions for making a wooden housing specifically for the front area of a G5 device. Could someone here help with creating more...

You can use a polarity detector app on your smartphone to figure out which side is North (+) and which is South (-).If you want to risk glue breaking loose and would rather not print the magnets into the piece, then you can just grab the models and...

Create a 3-D model of a train car. 4. Compare and contrast which shapes should be placed together to create certain objects. Audiences: This lesson is designed for high school students in geometry. Subjects: math, art, science Standards:...