hare 3d model

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

The new model isn't uploaded yet, but stay tuned for updates. 6/25/20 - This device has proven too effective. If left in the water for an extended period, it rapidly consumes the anode and produces copper oxide flakes. I can only leave it in for a...

The COMPLETE Bonegnasher Gnolls I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Gnolls were spawned by the Demon Raz'n'guul, born from a rotten tooth of the corruption god...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

## Computational model The library is built around the `bladegen` function. All parameters are supplied with default values, but you may want to change these. The `bladegen` will calculate a number of points along the blade radius called nodes....

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

You can use a polarity detector app on your smartphone to figure out which side is North (+) and which is South (-).If you want to risk glue breaking loose and would rather not print the magnets into the piece, then you can just grab the models and...

Print so that the models are standing upright, largest end down. <h3>Post-Printing</h3> <p>To disassemble the original turn signal, follow these steps:</p> <ul> <li>Remove the screws securing the lens and remove the lens.</li> <li>Remove the...

... heliostat not being able to rotate 360 degrees (since that would tear the MLI).The rover design is merely a representation of a possible movable platform and the focus of the design lies in the heliostat itself. Rover wheel model is by Daniel Loera.

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

(Rotate these angles accordingly if you rotate the model.) This way, you will have two layers of crossing extrusions in the spine folds. This makes for much stronger, long-lasting book hinges.</p><p>For<strong> print-on-print</strong> technique (used...

Please note the Modular Assembly Preview STL is just to show a preview of one assembly model, not for printing. Here's a brief description of the types of parts included. Cuffs - Number is the inside diameter of the cuff. Diameters include...

Cursed Immortality Season 2 - (2/4) The Umbratouched - Curse of Vengeance   Description Save money on this complete December Bundle, The Umbratouched, Curse of Vengeance, which contains all the models from the December release! These models come...

This project is intended for use with circular lenses that are delivered in glasses ordered from Zenni Optical with this particular frame: https://www.zennioptical.com/p/metal-alloy-full-rim-frame-with-spring-hinges/5500 For either model of Quest,...

This meant adding three holes for screws, and I also added flanges on the bottom in an attempt to mount the fan shroud I modified for my model cooling fan shroud. I left the sensor port alone for now - I may or may not try using the cooling fan...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

... for the bottom of the case i used this * Various wire, soldier, etc. etc. My Other Stuff: https://cults3d.com/en/users/revere521/creations https://www.printables.com/social/406094-revere521/models https://www.thingiverse.com/revere521/designs

Found a simple hip flask just laying about USHip flask discovered seemingly abandoned USHip flask uncovered, left behind USHip flask in basic design chanced upon USHip flask, a basic model, was stumbled upon USHip flask, plainly designed, was located...

I have no model or figure of Buffaloman in a camo tank top. The bazooka is actually pointing backwards to simply be held resting on his shoulder. I scaled it to 40% and positioned it to be resting between two shoulder spikes with the hand grip...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

Print the model as is for the Front piece and MIRROR the part Z axis for the Back part. Position the part on its back with the legs sticking up, then rotate to 45 degrees to make it fit on your bed. Print the Front (part)... Then print the Back...

Research I found two suitable models on Thingiverse which I thought could be easily enough modified: Tweezers for SMD by Ruslan_Kulibin SMD Test clamp by Tom20170 which I both printed yesterday. They are both quite nice designs, I especially like...

Except for the Sunlu mount plate just lay the models flat. The Sunlu mount plate I printed standing upright - even without support (although some minor bridging is needed, but that was no problem)</p><p>As mentioned above, the hygrometers are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

Although mine is 17mm long you can scale this with your slicer (Z axis only) when you slice the model to change the space from the wall. Use as many as you need around the edges, corners and middle parts of the perforated board.</p> <p>The spacer...

Thread the wire through the lower cutout of this model and attach the new wire to the switch by pushing the two quick connectors onto the switch's terminals. ...Press the switch into its place in the case. </p><p>Cover the electronics (<a...

Orient the model on the flat surface in PrusaSlicer then paint supports on the lower edges of the camera shroud. Set supports for enforcers only.AssemblyThe Raspberry Pi 4 (I used a 4GB) and camera V2 are held in place with a couple of screws each. ...