hera arms linear compensator 3d models

It looks like you've got a table with some planetary models and their corresponding scales. Here's the cleaned-up HTML for it: ```html <table> <tr> <td><a href="https://www.thingiverse.com/thing:3720464">Earth</a></td> <td...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A wise monk who was captured, tortured and blinded after speaking out against the cruelties of Irinax’s followers in Iriksha. His blindness is now a blessing, for he does not bear...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

WORK IN PROGRESS Modeled off of reference pictures, many dimensions are guesses. This is intended to be a NON-Firing, but bolt operable, replica. can be printed entirely in PLA (if possible, the charging handle and magazine spring is better...

Select model on plate -> right click on it -> Add support enforcer -> Load..) Assembly Mounting the whole thing onto the printer is a bit fiddly. Here's how I went at it: <ol> <li>Remove the case from the hotend carriage and remove the old radial...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0 custom_bottom_port_length = 40...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Add one if you have adhesion problems.Dimensions and Part NumberingYou find models for many combinations of heights and depths. The heights are in the range 35mm – 100mm and the depths are in the range 80mm – 190mm.</p><p>These numbers are included...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

A lot of the model are just perimeters or solid bottom/top layers. The pass-through holes for the cables create small bridges first and they are closed first, and then the top cover is printed. ...So I made a few arrangements to allow decent printing...

Assembly Video: https://youtu.be/GqohsdSTQrc Using"2mm Male Female Banana Plug Connector for RC Model ESC Motor Speaker" to convert Foster Connectors to electrical connectors -concentric BNC like. The printed parts hold these 2mm contacts in place...

I need thosethree measurements from that photo: Front standoff spacing, back standoff spacing, and front-to-back spacing.I've already helped several people from across the globe and I've been updating this document with the new models as I go.Post...

If you print this, you won't need to print the motor_plate-beta10.stl as it directly replaces it.     These parts are the latest as of 28 April 2022, if the VORON team changes the motor_plate drastically it will no longer work.     For those that...

I've uploaded the STEP files, so feel free to remix the system to fit your printer model! Just give me a shout-out because it took a lot of hours, dozens of printed iterations, and plenty of PLA. The IR Probe is mounted to the connector by design...

So it was time to change the software for a version with customizable options. version 0.1 detail Version 0.2 is a rebuild of the FreeCAD model in OpenSCAD. While working on it some additional settings beside the number of legs made sense. Now there...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

... clean it up. &nbsp;Pictured below are the on edge views of the dove tale design and the individual prints used in the above picture.If you decide to model your socket or light switch cover, the dove tail profile I used is shown below (units in mm).

A hard case for your Eggtracker Mini to use with high power model rockets. Bill of materials: Eggtracker Mini (only tested with rev C3) Turnigy Nano-Tech Plus 300mAh 2s 70C Lipo Pack (hobbyking, amazon, search around and try not to get raped...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

the tabs are at different positions on each model. * Group Token Holder - slots in behind the main card holder. * Player Holder - holds the large Agent Pawns. * Player Tray Base x 4 - print these in the 4 player colors. * Player Tray Top x 4 -...

*Note: don't order a GearVR with a white body - it is a 2015 model with smaller lenses that don't fit.* **UPDATES** **V3.3** (slight comfort improvements over v3.2). [print 1 for each eye] **Added a version for the prescription inserts from VR Lens...

The shade is 196mm high - be sure it fits your printer's build volume. Print it in white or even translucent PLA. The model has been adjusted in Meshmixer to be solid. You need to print this in <strong>Spiral Vase Mode</strong>! This will print the...

Got home from work, so now it's time to work: My initial model idea looks nothing like what I later end up with. Its bulky and more suited for clipping onto a credit card. The idea was there but not the form. I just kinda thought of the idea and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_shape = 3 custom_right_port_length = 30 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...