hiletgo esp32 schematic 3d models

A very simple enclosure for the ESP32 D1 Mini (WEMOS or clone) Print instructionsI printed this with the filament I had loaded at the moment...specifically ESun 3D PETG Fire Engine Red. I printed with 0.25mm layer height. This is a prototype...a...

A simple case for the Esp32 DevKit of the model in the picture, with 38 pins. and standoff holes. INFO: The weakest part of the print are the standoff pins, however, they are not really needed, two can break but the case will work just the same...

For ESP32-Wroom-32D (wider version 2). Version 1: the processor heat is ventilated via three 4 mm holes. Sensor is in its own space.Version 2: the processor heat is ventilated via 2 mm holes in 45 degree openings as well as sensor ventilation.

I have built an ESP32 radio (https://github.com/Edzelf/ESP32-Radio) on a 70x50mm perfboard. The following key-components were used: Speakers https://www.aliexpress.com/item/4000127737256.html?spm=a2g0s.9042311.0.0.22f54c4devAQBT MP3 decoder VS1053B...

I have built an ESP32 radio (https://github.com/Edzelf/ESP32-Radio) on a 70x50mm perfboard. The following key-components were used: Speakers https://www.aliexpress.com/item/4000127737256.html?spm=a2g0s.9042311.0.0.22f54c4devAQBT MP3 decoder VS1053B...

** Parts ** ESP32 TTGO T8 https://s.click.aliexpress.com/e/_d6sfNUb RX5808 https://s.click.aliexpress.com/e/_dUaM1rh 2x 4.7K resistors Small battery (optional) i.e.: https://aliexpi.com/ZSsn Buzzer (optional)...

This is the enclosure designed specifically for the ESP32 Marauder.\r\n\r\nKey components of the project:\r\n- The ESP32 Marauder\r\n- 4 M2.5x10 Hex screws\r\n- Enclosure face plate\r\n- Enclosure body\r\n\r\nHow to assemble the enclosure:\r\n\r\n1.

I have built an ESP32 radio (https://github.com/Edzelf/ESP32-Radio) on a 70x50mm perfboard. The following key-components were used: Speakers https://www.aliexpress.com/item/4000127737256.html?spm=a2g0s.9042311.0.0.22f54c4devAQBT MP3 decoder VS1053B...

On github you will soon find the list off all electronical components and modules, the electronical layout and the code: [Project code on github](https://github.com/thorgal11/esp32-fpv-rover) When started, the ESP32 inside the rover is connecting to...

I made this design to use it with ESP32-CAM and a MicroUSB board to plug it.To have the thinnest case possible, I cut the PINs that are too long.ESP32-Cam on Aliexpress hereMicroUSB Board hereTutorial to configure it with tasmota firmware here (In...

Required components besides the two printed parts: wrover esp32-cam module two nuts M5 four screws, 60° head, M3x16 (screwed directly into the plastic) For best firmware I found for this module, please refer to this GitHub repository:...

The two teardrop-shaped holes require filling with a translucent material, which will diffuse the ESP32 T8 LEDs. You can achieve this using a 3D pen and translucent PLA, as seen in one of the photos.\r\n\r\nFor more details, check out...

For information, the ESP32 T_Display board manufacturer is here: http://www.lilygo.cn/prod_view.aspx?TypeId=50033&Id=1126&FId=t3:50033:3 The development boards are attractively priced and can be purchased from many outlets, including here:...

... The lid is a one lid fits all. I hope this helps someone out: Box i built for Sound Reactive builds of WLED to attach a microphone: https://www.printables.com/model/317718-esp32-wled-sound-reactive-box https://www.thingiverse.com/thing:5631371

I bought this ESP32 ( https://www.aliexpress.com/item/32819907815.html?spm=a2g0s.9042311.0.0.39b54c4dZwsiTr ) to integrate in Home Assistant, but I did not like the "naked" look, so I decided to create a simple enclousure. It has no locking...

This base has four 11x3mm cavitys for 10x2mm magnets on the backside.To watch our powermeter via "ai on the edge" firmware on the esp32-cam modul + green USB micro breakout board, I needed a flexible but sturdy solution to get the position right.With...

Components: - 4 standard 6mm potentiometers (linear 10k ohm) - 2 KY-023 joystick modules - SSD1306 128x64 1.3" I2C OLED display - ESP32 (DOIT DEVKIT V1) - nRF24l01 PA+LNA 2.4GHz module - 4 DPDT switches - 2000mAh 5V USB powerbank The bottom and top...

DIY Case for ESP32 V1 DIY board by AWOK, to be used with board from [AWOKMUSIC](https://awokmusic.square.site/shop/electronics/3?page=1&limit=60&sort_by=category_order&sort_order=asc) Holes are made for 4 14mm m3 screws *Be sure to double check the...

Simple enclosure for the very nice ESP32 Louder Board from sonocotta.The lid is angled on the short sides, so that you can "clip" it on the base.Maybe you have to edit the tolerances to fit if your printer is better calibrated then mine.Added some...

I'm working on a project using an ESP32 to read temperature and humidity data from Bluetooth sensors. As I moved around the house to set up the initial prototype, I made the decision to quickly assemble a makeshift enclosure for it. The current...

Rhasspy Dot Case for Matrix Voice ESP32 and Speakers Slim modular offline voice assistant case Assemby: print all parts glue the fabric to the cover - i used superglue cut the fabric leftovers from the cover mount the matrix voice hat with 2 small...

I adjusted it a little because I wanted to connect the ESP32 with a USB socket. To do this I had to enlarge the case and create a new lid.In my case, the glass on the water meter was extremely reflective, so I installed a lens on the camera light for...

There is plenty of ESP32 board enclosures out there, but most of them are quite streamlined/minimalistic, which is fine but I set out to buid an enclosure with a little more room in it so you can easily use breadboard jumpers instead of soldering,...

... and time information by previously synchronizing its clock through an NTP server. This transmitter is built from the ESP32 module, coupling a small 64x48 pixel 0.66-inch OLED display. ... First version: https://www.thingiverse.com/thing:3601407

Modified this Mech to take my ESP32-Cam was worried about the heat but so far no failure. The original poster of this model was given the blues for it. If you can't figure out what to do with it don't make it. the camera needs to be hot glued to the...

There is plenty of ESP32 board enclosures out there, but most of them are quite streamlined/minimalistic, which is fine but I set out to buid an enclosure with a little more room in it so you can easily use breadboard jumpers instead of soldering,...

This nano data center is based on a Wemos D1 min ESP32 and has a 24 neopixel ring integrated (for optical alarms etc.) and a SPI port, for external connection of a nRF24 or LoRa module, is provided. All parts stick together and hold. No glue or...

Window mount for your ESP32-CAM board Mounted with double-stick tape directly to the window make it possible to stick inside to show the outside with minimal reflections. The mount tilts the camera upwards and not straight forward. Used as a...

... The case can be clipped onto the heated bed (with bull-dog paper clips) and they look directly at the nozzle. You'll need to flash the ESP32 CAM with the camera web server or with the file described here: https://www.youtube.com/watch?v=6qiH1BRwUeA

... The lid is a one lid fits all. I hope this helps someone out: Box i built for Sound Reactive builds of WLED to attach a microphone: https://www.printables.com/model/317718-esp32-wled-sound-reactive-box https://www.thingiverse.com/thing:5631371