x one2 3d printer

This is a copy of the nameplate on the front of the QIDI X-one2 printer. It includes an embossed logo and text which stands 1mm above the face of the nameplate. ...

This is a simple cover which snaps over the spool nut on the inside of the printer. It's a really, really odd thing to print, but it fits well. Made to match the style of the other QIDI parts I've printed. ...

I couldn't find any tool/accessory holders for the Qidi Tech X-one2 (found for the X-one, but it didn't fit), so I designed it from scratch.  These do take a while to print.  Supports are not required, but depends on the reliablity of your printer's...

It has the same basic design, but the measurements for the X-one2 to include the added plexiglass panels on the sides. I only have one done and will work on the other if this works. I'll keep this updated on the progress. So far, so good. ...

Print Settings Printer: Qidi X-one2 Rafts: No Supports: No Resolution: 0.2mm Infill: 15% Notes: UPDATE 4/12 @ 2pm: Finally got around to printing the Version 2, and it works and fits great. I am going to remove the little slot I made, just b/c it...

Filament spool attached to handle of X-one 2.

Please disconnect from mains power before removing the base from the printer otherwise mains voltage live parts are accessible. The brackets are a snug fit and require a little wiggle to locate, the fascia is simply a friction fit over the whole...

... with my fingers. i suggest you check your limit switch & surrounding area carefully just in case YOUR X-one2 is a little different from MY X-one2. ... printed in PLA .2mm layers with support 2.0mm walls & 50% infill for a good strong part

The fan mount on the left side is a little tight but does fit the original x-one2 fan. ... The extruder cooling fan currently only works with one bolt but i'm in the process of fixing that.

Hotend cooling fan duct for Qidi x-one2 printer. Idea from that one made by rpagyc, but with few improvements. Two side blower with Bigger, separate air duct, better air flow. Printing quality and bridging are much more better then the Qidi...

I wanted to add a simple microswitch filament sensor to my Qidi Tech X-One2. The idea for this came from: https://all3dp.com/2/ender-3-filament-sensor-runout/ There are designs on Thingiverse, but their suitability is dependent on getting a...

I wanted to add a simple microswitch filament sensor to my Qidi Tech X-One2. The idea for this came from: https://all3dp.com/2/ender-3-filament-sensor-runout/ There are designs on Thingiverse, but their suitability is dependent on getting a...

This is a simple, lightweight x-axis stop for the QIDI X-One2 and X-One printers. You’ll need one of these if you remove the shroud that sits over the print head. I chose to ditch mine to give me better access to the extruder. ...

Customized version of https://www.thingiverse.com/thing:34558 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=34558

... bicycle brake cable adjuster works perfectly as a filament guide. On my X-one2, I have an alloy extruder feed and the bicycle cable adjuster threads right in. The one pictured is from a Shimano road caliper and features M6x1.0 threads. ...

This is a PTFE tube cutting jig for the QiDi Tech X-one2 printer.

This adapter will enable you to use a filament spool with a [roughly] 3 inch hole on the Qudi Tech X-One2 filament spool holder that came with the printer (which has a [roughly] 2 inch hole).

I will probably make a new part that includes the plate and upright into one part once my Ender 3 gets here, but the bed size on the X-One2 limits the size and it would be cheating to put a mod out that doesn't fit the bed of that printer. Without...

This is a remix to fit the new Qidi X-One2 model without the metal handles on the side. Can be printed on 3 beds or use the "Full Holder" file to print all 3 on your bed at the same time (its about a 12 hour print all together). ... Print all three...

These squares are used to level the build platform of the Qidi Tech X-one2. Print at the recommended temperatures for the filament you are using. Print at 0.2 mm layer height. These squares will only print one layer and you can use this to help level...

Tilt the little leg to hook it onto the underside of the handle, then plop it down onto the printer. It can migrate front-to-back on the printer, but can't slide off side-to-side. Could benefit from the addition bit of a little magnetic tape. ... ...

I made this because I kept having jamming issues with the original spool holder that comes with the printer, and I saw a lot of complaints about it online. The pieces are designed such that they all fit together. ...The tolerance should be tight...

I made this because I kept having jamming issues with the original spool holder that comes with the printer, and I saw a lot of complaints about it online. The pieces are designed such that they all fit together. ...The tolerance should be tight...

This is EDGE X, a compact, low cost 3D printer. It has a few new features... Coming to instructables soon. -Update - May 1st 2017- This project has NOT been abandoned. Far from it. I just updated the .svg file and main image. The Edge X line will go...

This is a spacer for the Qidi Tech X-one2 printer that adjusts the Z-Axis stop height when using a borosilicate glass plate on top of the metal build surface. It fits snugly on the back of the Z-Axis platform in between the two metal rods. Versions...

This is a spacer for the Qidi Tech X-one2 printer that adjusts the Z-Axis stop height when using a borosilicate glass plate on top of the metal build surface. It fits snugly on the back of the Z-Axis platform in between the two metal rods. Versions...

For printers that use the 6mm (4mm ID) filament tubing to support the wiring harness, like the QIDI X-One2, this presents a problem if you decide to use an alternative method of feeding filament into the extruder. For our printers, we're feeding the...

... zip tie. ...I needed to do this because one of the ring clips on my printer broke. Make sure both screws are threaded before you tighten either. The fit may be a little tight. ...The replacement zip tie can be run vertically through both tie holes.

This is the x-carriage of the Ormerod 3D printer from RapRepPro.

X-Axis Carriage for a 3D-Printer with an included Motor mount.Has an integrated belt-tensioning system.Requires M3 knurled inserts, M3 nuts and M3 screws for assembly.