hue bridge versions 3d models

Most of my light switches required the switch to slide on the opposite way from the original cover due to door frames being close but I have included both the left and right version. Left adapter is for if the door frame is on the left and right...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Version 3 included 2 hooks for hanging items ###MaterialsMagnets You will need 2 magnets 6.3mm x 3mmhttps://www.michaels.com/promag-neodymium-magnets/10413548.html Super Glue You will need some crazy glue to secure the magnets in...

Customized version of http://www.thingiverse.com/thing:287025 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options:...

I have now uploaded an 22mm wide version https://www.thingiverse.com/thing:6141963 When printing the small parts I found it helps to make sure I have a clean bed, cleaning it with window cleaner does the trick for me. I tried it when I didn't have...

Remixed from: https://www.thingiverse.com/thing:4248444 https://www.thingiverse.com/thing:4614658 https://www.thingiverse.com/thing:2506910 https://www.thingiverse.com/thing:3853037 https://www.thingiverse.com/thing:3853049...

Hardware used: FC - Naze32 rev6 (direct soldered wiring, no pins) ESC - DYS 4in1 20A MOTORS - Racerstar 2205 2300kv PROPS - KingKong 5045 Tri's (with 5mm tip trimming) RX - FRSky R6b (decased and unused pins removed) BATTERY - ZOP Power 11.1V 850mah...

doing so they practically become 3 versions each you will need:Printed parts1 - game board4 - poles1 - maze of any level you want Not printed parts4 - rope sections of 30cm each (you can use whatever rope you have on hand, from a shoestring...

Customized version of http://www.thingiverse.com/thing:287025 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options:...

The post included in this model is the recent version with four feet so you can also mount it on the rail sideways. This may open possibilities for other functionalities in the future You will also need the following parts *Bearing (4 pcs) Item...

Customized version of http://www.thingiverse.com/thing:53235 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: crankSlack = 1.8 times smaller gear_tolerance = a...

DesignThis is an advanced version of our original nologo!SKATE spool holder with some advanced features you might find useful! Since we are really printing a lot and mostly with big spools we were always skeptical of mounting the spools to the...

I found that earlier versions broke across the layer lines when I printed horizontally while printing vertically places requires a lot of difficult-to-remove support material. Printing at a 45-degree angle was a good compromise between strength and...

The number of attachment points will depend on the size of the bottle, my 8L bottles need 4 points. Print in PETG, the slight flexibility is super for the clip-on version. Printing in PLA may very well result in the parts shattering and cutting...

It is simple to manufacture, and relies on the following non-printed parts: 1x NEMA 17 geared stepper motor (5-1 gear ratio)...

this mount can be used with the 68 cal version of the UNW P90 mags that holds 28 rounds. as you can see on the pictures are there a view options when it comes down to the front morning part. this is so you can have custom look. but at the same time...

In the past I would print multiple versions; each time a made a change. ...I'm really proud of this design and I hope you enjoy.</p><p>&nbsp;</p><p>This is also Thingiverse Thing <a...

... <p>100%</p> <p><strong>Notes:</strong></p> <p>Print at 100% infill. The tubes are modeled hollow and should print that way Post-Printing Top Finishing Some finishing may be required for the Elite version of the top. Category: R/C Vehicles

    This 3D print product lets you print a large number of Mothman- and shrine-themed scatter terrain to help build and elevate your tabletop scenes.   Files have been pre-hollowed where possible, and all files include supported versions for easier...

There are two versions of a motor ESC holder (Square tube doesn't need this) one loops round the tube to give a flat surface, the other is held by cable ties. Just tie the ESC to this. You can put the ESC in the body if you prefer, or hold it on top...

All the pieces need to be printed flat, without support.To print (3D):Zoetrope-praxinoscope (or if you don’t want a praxinoscope, just the zoetrope.)There is now a narrow version of both, the slit on top are narrower;Base MBase ZConnectorManivelle...

I'm working on a smaller version that will use filiment rivets instead of pins. Currently, the hand crank is too small to turn the load so the center needs to be turned by hand. I plan to add a motor to it. Stay tuned. Assembly: A. Assemble the...

I also have a version of this tube which extends from 50-150mm, for shooting at 1-3x magnification with 50mm lenses: https://www.thingiverse.com/thing:4941924 (it can no longer focus to infinity, though) ## More macro accessories Pictured in the...

The software was designed using Arduino IDE version 1.8.5. Note that this is my first experience with HTML, JavaScript, and JSON programming, so please be gentle in the comments. ... And finally, the case was designed using Autodesk Fusion 360, sliced...

Do note, this is only compatible with the soldered version of the PCB.There are 4 "layers" to the design: the top, plate, bottom, and ramp. The plate holds the Cherry-MX compatible switches, and once the switches are soldered in, holds the electrical...

Modeled after a 1915 candlestick phone, early versions had no dial because you just lifted the earpiece and clicked the lever a few times to get the operator's attention and told her the number or person you wanted to speak to. This is a fairly good...

I created several versions of the lock inside the object, but this one works best. This particular lock configuration disguises the orientation in which you need to hold and manipulate the object when unlocking it, making it less likely for someone...

I use the SMD version of the transistor and solder it directly to the board: the gate to GPIO5 (D1 pin), the drain to GND and the source to the LED. But you can use a more traditional through hole part replicating this wiring. 3. Power switch:...

This is the third version of the SCAD file I've uploaded, with improvements including proper tab positioning on the trapezoid and parameters to adjust its position when twisted. If you encounter any issues or have suggestions, feel free to let me...

Their remix has a nice lip, so this should make the cover a lot more sturdy (see the first picture). You'll need to reprint Part B as well as I had to shorten it a little bit since I changed the placement if the chain attachment. The new files are...