ide to compactflash adapter 3d models

This remix adds bottom screw holes to the adapter that are required by some old laptops (e.g.Apple PowerBook 1400 series). ...Only 3 of the 4 bottom screw hole positions used by real old hard drives were able to fit.

... cover. Required: (x8) M3x5 mm screws for single IDE To SD adapter (x12) M3x5 mm screws for dual IDE To SD adapters Optional: IDE extension cable ----- The 3.5" drive bay version is available at: https://www.thingiverse.com/thing:5642213 -----

ORIGINAL SUMMARY [I didn't designed this Thing, I ONLY corrected the error from the STL file] ORIGINAL CREATOR: https://www.thingiverse.com/dogp/designs This is a bracket to install a CF->IDE adapter in an internal 3.5" hard drive bay. I collect...

... may need to be glued down to the PCB to minimize light leakage between the LED holes. The floppy style power connector is blocked, so you will have to use the Molex connector next to it to power the adapter. ... FreeCAD files are included.

Remixed from "PCI / ISA Slot Bracket for IDE 40pin to SD adapter", this adds the following enhancements: - Thicker triangle areas along the bracket so stress from inserting/removing the SD card doesn't flex the bracket as much. - Enclosed bracket...

Remixed from "PCI / ISA Slot Bracket for IDE 40pin to SD adapter", this adds the following enhancements: Thicker triangle areas along the bracket so stress from inserting/removing the SD card doesn't flex the bracket as much. Enclosed bracket screw...

 The housing should be seated as close to the PCB as possible to avoid leakage of light between the LEDs.The floppy style power connector is blocked, so you will have to use the Molex connector next to it to power the adapter.FreeCAD files are...

 The housing should be seated as close to the PCB as possible to avoid leakage of light between the LEDs.The floppy style power connector is blocked, so you will have to use the Molex connector next to it to power the adapter.FreeCAD files are...

Adapted from https://www.thingiverse.com/thing:3543297 to a low profile bracket.

Based on clockspot's adapter, but reduced to fit 7mm hard drive cages. ...Made originally for a Toshiba Libretto 50.

... This slot adapter is designed after a 3.5" floppy drive's dimensions to fit neatly into those slots. ... There are several different versions of the SD boards available; I'm not sure which one he has, so compare with the pictures provided.

This is case for cf to ide converter. I'm using it this ZX Spectrum and divIDE. You may use it with Amiga/PC or other devices that supports IDE devices. Cover closes box via frictional fixing. Source files are there - you may change everything. ...

This 3D-printable adapter accommodates a Startech "IDE2CF" adapter and modifies it to fit the RISC PC's one-of-a-kind hard drive compartment. First, attach two 5mm M3 standoffs (PC motherboard standoffs work perfectly) to the holes on the top...

This is a simple adapter to hold a CF-IDE in a 5.25" drive bayThis is the compact flash IDE thing I use...

Drive sled for a SD to 44-pin IDE adapter. Use a M3 pan head screw (old PC one works best) to hold down the card. ... https://www.tinkercad.com/things/iYtA5puL7rm

I just did a quick tinkercad bad remix on the original to get it to fit correctly on my setup. ...I figured I may not be alone here so uploading for others

... 900/1200 cases or the old IBM XT clones. Can print flat without supports, or on its face with minimal supports. This is designed to use the generic SD to IDE adapter that is available all over Amazon and newegg. ... Fusion 360 file included.

Designed for SD to IDE 3 LED's adaptor with rear bracket

Holder and 2.5" HDD mount for the CF-to-IDE V.H2 board. ...It uses the protruding bottom of the jumper pins in combination with the rails to keep the board in place.

However the manufacturer only provides a bare PCB with no enclosure to allow it to be easily mounted.So I decided to take on the challenge my self of making a 3-1/2" drive bay enclosure for my SD to IDE adapter.This project will require some basic...

For a project, I needed to mount an SD to IDE adaptor under the CDROM and out the side to the little side cover on the desktop version of this Optiplex (Replacement side cover also uploaded) I've also included a simple flat one with just screw-down...

Here's the original text rewritten using the same tone and voice: This is a PCI slot holder for a low-cost SD to IDE converter manufactured in China, specifically designed for attaching an SD card reader or other small devices directly to the...

This is a remix of a SD2IDE Adapter allowing to change the SD without disassembly.

A straightforward and uncomplicated CompactFlash card layout is being implemented.

I'm a professional photographer at my Photostudio, and I use this versatile holder to store up to 12 CompactFlash cards at once. It's a vital tool for me to keep my workflow organized. Printing Settings are crucial in bringing my creative vision to...

Tidy up the CF IDE adapter easily and securely under the TF328, where you prefer to position it. Printing takes around 6-12 minutes, depending on your printer and settings. ...A layer height of 0.2mm works well with 100% infill.

Mount a bracket specifically designed for Satechi's SD to IDE (40-pin) adapter, allowing it to be securely fastened within a standard 3.5-inch HDD bay. Carefully crafted threads on the sides and bottom are threaded for #6-32 UNC screws, which is the...

A simple thing to tidy and help secure the CF IDE adapter under the TF328 (if that's where you want to place it). Prints in about 6-12 mins depending on your printer and settings. ...0.2mm layer height works well with 100 percent infill.</p> <h3>Print...

A simplified variant of @shawndw_ca's bracket - this has less fiddly bits, and the screw holes are reduced in diameter to allow for tapping with a suitable M3 die.

If you're threading the ribbon cable around an edge of the PC chassis, you might want to put some tape around that edge to ensure it's not sharp.Usage NotesIf you're using a CF-IDE adapter for your retro computer, but you want easy access to the CF...