ipod touch dock 3d models

Contact Us: If you have any questions or want to get in touch with us, please don't hesitate to reach out. You can find us on social media at Twitter (@3dmodularsystem), YouTube (youtube.com/c/3DModularSystems), or visit our website at...

I think I might have forced it too much though, as I tried to touch the two lips without the rod so the flex was too much for PLA to take. As a result, I reinforced a bit the thin side at the rod hole level, as you can observe from the attached...

This was designed to fit to the Mossberg 500 lower shell tube and does not touch the barrel when installed properly. Anti-rotation is provided by incorporating a small section of 1/16" rubber packing sheet (see link below). Rubber sheet section...

There's no under/over extrusion, and any wacky spots are well within the feed rate override (I haven't touched it and printed most of the awesome MPCNC files and my upcoming Mostly Printed Quad Copter with no issues). Update 7/1/19: There was a...

This is a stunning tensegrity sculpture composed of two intertwining helices that appear to float above one another without touching. Four tensile members support the upper structure, while the base and top of each helix form a regular tetrahedron. I...

It should be pushed ALL the way through the adapter and touch the top of the Mosquito. You need about 6mm of PTFE sticking out the top of the Adapter. Make sure you bevel the inside of the PTFE only at the top of the tube. This is so the filament...

Straight away, the Therion's flaming claws are swiping at the goblins, incinerating them with its touch alone, sending their burning bodies flying this way and that into their ranks.  Ifrit smashes them, throws them, eats a few and ultimately leaps...

It's a good idea to give it time to melt on a low temperature and to let the wax cool until you can touch it with your finger without it hurting you ( it wil be +-40°C) before you start pooring it in the mold. If you have some ABS or an other...

For all dice set the support overhang angle to 43° and "touching builtplate only. Use high quality setting to get the best possible result and set all walls to the same thickness so that you don´t get unbalanced dice. Set the infill to minimum 25 %...

- Layer Height: 0.16mm - Wall Thickness: 0.8mm - Wall Line Count: 2 - Top/Bottom Thickness: 0.64mm - Layers: 4 - Infill Density: 20% - Infill Pattern: Triangles - Printing Temp: 200°C - Build Plate Temp: 60°C - Printing Speed: 60mm/s - Initial Layer...

... Decorate your recently revamped kitchen with one of a kind and utilitarian kitchen furniture to add that individual touch to which you have for practically forever needed to improve your kitchen.https://www.justnewsday.com/kitchen-furniture/

Rear hex is shorter because if you use front hex, it will touch the rear axle. Friendly note: 1. I suggest you to print hex in black color to highlight the style (design). 2. I print in 0.2mm resolution 15% infill (feel free to print it in...

:) Support settings: Placement of the support - touching the print bed Angle for support overhang - 46.0°. Pattern of support tower - gyroid For dimensional accuracy of the print, the experimental setting Slicing Tolerance "Exclusive" in Cura has...

The holders are so high that when you push them in, they touch the lid with a small resistance, thus closing the box. On the bottom of the carrier plate, the height of the discs is shown in recessed text.</p><p><br>The third component is the lid. The...

It will be assumed you have already experience assembling/servicing the whole X carriage here.On the bottom rod the grub screws will be touching the metal directly and could damage the hardened surface. This is not a problem usually as the end of the...

Thanks to biniecki for the heads-up, and further thanks to user JDPenney for letting me know about the two other designs (and for helping me with my firmware!) _______________________________________________ I upgraded to the rather nice BigTreeTech...

This is my improvement of the beautiful DIY Low Cost FPV Goggles by markvanhaze: http://www.thingiverse.com/thing:583508 \nModified mask piece by attaching these beautiful ski goggles: http://www.thingiverse.com/thing:278294 \nThe mask piece is now...

Yours may be different depending on the manufacturing "quality". An excellent informative tutorial on vinyl cutting with your CNC can be found here. A video about setting up the drag knife. And this one is very good, has a few important tips. And...

Each fixture is not created with just numbers and tech data in mind; instead it is truly made by skilled designers combining artistic touch, advanced understanding of what goes behind making exceptional lighting systems. ... A note from the creator -...

... anchorpoint at all needed heights, just supply the layernumber as y-coordinate to get different targets. These can then be altered with the search&replacee-script to the desired command. Once configured you don't have to touch this again. ...

The aim is to gradually glue the prepared weight (nut M8-M10) into the back space, as close as possible to the lower edge of the thorns, to achieve a state where the hedgehog, built on a horizontal surface, stands still on its hind legs and falls to...

Feed the string through the hole in the servo, and pull it out until it's *just* loose, and the screws are still touching. Now stick a 3mm M2 self-tapper (or other screw that fits) through the hole in the servo arm to retain the string. Connect the...

- 3mm screw for the powersuply and 2/2,5mm for the cable tensioner - (optional) TTP223 capacitive touch switch - I prefer to always have hardware on/off switch on my lights in adition to wifi control. - car fuse holder with adequate fuse - actualy...

It shows the exact print for the PrusaSlicer example project.Explore More 3D ModelsCheckout the following blog post for a visual overview of all flower pots and saucers I designed:Designing 3D-Printable PotsI warmly invite you to browse my other 3D...

No screwing or gluing is needed but ensure that the Trigger part would go to the very end and touch and nesting on the holes of the Y-Carriage Plate. Testing: 1) Power up the printer and turn on the Main Switch. 2) If the Slide Switch is at "on"...

I used PETG for this. Step 1: Use a 3D modelling program (i used Fusion 360) Step 2: Create a solid layer which is as thick as your first layer (0.2mm for example) This first layer will be the layer which touches the print bed. I used a glass bed for...

Use a square piece of rubber that fits into the hole (corners almost touching the inner thread of the cover / 27mm x 27mm). It doesn't have to be attached, it stays there. Don't cover the whole area with a circular seal. A piece from a bike innertube...

Note: You may touch the soldering iron on the cooled solder to heat it up and try to form a perfect bead or bubble to conserve space, but if you fail the first time, that's okay. It won't affect performance. Make sure to do the same to the "B+" or...

You can connect your computer again with the touch screen plugged in as long as you don't do any firmware uploads to your printer. - Send some movement codes to your printer to see if all is working fine, if not you can change the direction of the...

And the fuselage needs 10mm of hex 10% infill to create a firewall and space for the battery tray, without these 10mm the battery tray will not touch the firewall. Better use the .factory or gcode files. Basic specs Print weight: +/- 850 grams...