k40 laser alignment 3d models

K40 Laser Alignment

This is to help when you align the K40 laser mirrors. You will need to cut a piece of metal from a soft drink can (or a soup, baked beans ect. can lid), approx 24x32 mm. This gets inserted as shown by the blue shield in the first image (there will be...

After printing a different unit where it is on the table side of the K40 laser and it getting in the way of the drag chain. I decided to make it for the opposite side of the back wall. Also used a magnet from a old hard drive. Have alot of...

this requires no tape, no power through your laser, and no cleaning of the tape residue after alignment. overall seemingly less hassle. move carriage to furthest corner and work backwards aligning. ... just toss a cheap dollar store laser pointer in...

6mm laser pointer module holder for K40 Mirror alignment. ...

i ordered this: https://www.ebay.com/itm/Co2-Laser-Head-Focus-Diode-Module-Red-Dot-Position-DIY-Engraver-Cutter-5V-K40/172731687856?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649 and it didn't fit so i modeled this to take a 26mm head...

This is an alignment tool for a Chinese k40 laser engraver. The tool is suitable for the laser head with a diameter of 26mm. I have an aluminum tube used to align the tool in the head. You have to be careful not to damage the mirror in the head with...

This is a remix of DIY3DTech's: eBay Chinese CO2 Laser Cutter & Engraver Mirror Alignment Tools https://www.thingiverse.com/thing:1149832 To improve on the original design I did the following: 1) Redesigned it using OpenSCAD. 2) Measurements can now...

You can safely adjust the laser head each time without worrying about your paper moving because the center is going to line up each time. NOTE: This is a work in progress. Try to keep the square edges of the base straight. so that you can use the...

Useful addition for these tools: https://www.thingiverse.com/thing:2539512

The Radius area for the K40 Laser beam to go through is very small so proper alignment is key so as to not damage your Aligner. Just put 4 flat head machine screws facing outward in the crossbars with a nut, align it properly and hook up the Laser...

Laser beam alignment tool for the cheap Chinese K40 40W CO2 Laser. The tool has two parts, one for mounting on the mirror and one for mounting on the laser head. Using tape or paper to mark positions has the problem of smoke residues getting on the...

Laser beam alignment tool for the Chinese K40 40W CO2 Laser.The tool has two parts, one for mounting on the mirror and one for mounting on the laser head.Using tape or paper to mark positions has the problem of smoke residues getting on the mirrors...

Instead of checking alignment with a test fire of the laser every time I fiddled with the mirror(s), I mocked up this laser module holder so I could get real-time feedback from my mirror adjustments. There are channels on either side of the plug for...

This is a simple holder for a mini 6mm laser diode module that fits into the tube of a K40/equivalent CO2 laser engraver/cutter. There are channels on the side for the laser module wires to exit the tube to connect to a battery. There is a flange...

... to the head when using it to keep the lid closed. This is for the regular K40. Does not work on air assist nozzles. For a complete mirror alignment guide - check out this URL: https://k40laser.se/lens-mirrors/k40-mirror-alignment-and-leveling/

I designed some parts to enable a red targeting/alignment laser on a K40 laser cutter, using the main optics, but not interfering with the beam path or requiring splitters. I us a small Arduino Micro servo from an old starter kit, a NodeMCU...

Made my own K40 Laser Reverse Mirror Alignment tool. could not find a tool for 10mm red dot laser, so made one myself . Laser fits in tube and tool fits on the lensholder (remove lens first.) you wil find youtube movies for instructions al over like...

works with newer k40s and 6mm ebay lasers laser dots converge at the preset focal length to indicate cut location and optimal work distance. ...

Laser holder parts is changed for 12mm laser module holder. ...The original parts is this : http://www.thingiverse.com/thing:923295 Thanks for original parts creator.

I really liked the idea of this beam combiner setup but wasn't too keen on the idea of having to glue parts together to make it work. I changed up the beam combiner so that it uses M3 screws and has pockets for M3 nuts in the body. No need for the...

This is a simple reverse alignment tool that holds a 12mm diameter red laser module (the kind with a lens) on the laser head of a K40 laser cutter. To use it, you remove the lens and its holder from the laser head and push it onto the remainder of...

These are small holder and feet that will it a M8 machine screw head - necessary if you want to upgrade the K40 laser bed to a honeycomb bed as shown in this video: https://youtu.be/TaACY2SnOxg

This is a jig that holds a paper in front of the first two mirrors to easily see where the laser beam hits. ...

Here is my simple design for a K40 Focus alignment tool that uses two, 6mm, 5V red dot laser diodes that are very inexpensive and available on Amazon. https://smile.amazon.com/gp/product/B01ITK4PEO/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 ...

I just need one of these, so I chopped one off the original that had 2 parts.

... 5v laser diodes. Both of the allign exactly with my laser and when the 2 dots become 1 the item is at the right distance (and the cutting laser is in focus) * The "laser houder" (u need 2) is used from https://www.thingiverse.com/make:301584. ...

-print both laser alignment pieces -attach the laser holders to the alignment pieces with #2 screws (I think I used 1" long, which was a bit longer than needed) -attach the assembly to the laser cutter. I mounted mine to the existing holes from the...

Jig for aligning square material to the origin of a K40 laser cutter. ... These are the magnets I used: https://www.amazon.com/gp/product/B07QWMHGHZ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

https://american-photonics.myshopify.com/products/k40-reverse-laser-alignment-nut You can buy a “boresight laser” and easily make your own, these boresight lasers cost about U$12-20 online and I think that's what APC uses anyway. When you've got the...