laser cut pen holder 3d models
498667 3d models found related to laser cut pen holder.thingiverse
Giraffe themed phone and pen holder lasercut in 6mm wood and acrylic. ...Perfect for a desk or nightstand to hold phone while charging or during work. Also check out my Elephant Phone & Pen Holder: https://www.thingiverse.com/thing:2483253
thingiverse
This is a super-easy box which can be cut on almost any laser engraver / cutter. The DXF file has been formatted to fit perfectly on the 11 x 14 plastic sheets you can buy at home depot. I left the second box empty, to allow you to quickly put in a...
thingiverse
Sliding Z-axis with spring mechanism/rubber-band keeping pen or knife sticked to the paper/vinyl surface. ... Requirements: 2 x 4cm steel rod 6mm diameter 2 x 12mm linear bearrings (or however its called) and about 3 hours to print it out and put...
thingiverse
if you like this pen look at my profile i have several you can print in 3d or cut with a laser good luck and enjoy the impression
grabcad
if you like this pen look at my profile i have several you can print in 3d or cut with a laser good luck and enjoy the impression
youmagine
This display rack was cut using a Full Spectrum 45W gen 5 Hobby laser. Finished parts were treated with polyurethane thinned with mineral spirits. It is important that the material used is 2mm thick. Otherwise it won't fit together properly. Design...
thingiverse
... than the one that comes with the Anet A6/A8. ... To construct this spool holder you will need: (2) Laser Cut or 3D printed Base Pieces (2) Laser Cut or 3D printed Support Pieces (4) M3x15 Screws (4) M3 Nuts (1) 5/16in Threaded Rod (4) 5/16in Nuts
thingiverse
This is a simple stamp holder for building laser cut stamps. The bottom piece is attached to the holder with glue. The handle should mostly fit in the cross piece, depending on the kerf of your laser. ...Designed for 3mm plywood.
thingiverse
I wanted to laser cut a spool holder because I was bored, so I threw one together in auto cad. ...It works, I used 1/4" MDF and a 1/2" wooden dowel.
cults3d
You can laser cut this holder so that napkins can be easily accessible while in the kitchen or dining area. This holder is designed to hold 165mm x 165mm napkins. I first designed the pattern in Illustrator then imported a dxf into Fusion 360 to...
thingiverse
You can laser cut this holder so that napkins can be easily accessible while in the kitchen or dining area. This holder is designed to hold 165mm x 165mm napkins. I first designed the pattern in Illustrator then imported a dxf into Fusion 360 to...
thingiverse
Laser cut DXF files for Magazine storage. Instructions The original files from makercase.com. Modified to accept magazines or periodicals. Inside dimensions 12" x 10" x 4 inches. Made from 1/8"...
thingiverse
###Coin Cell (CR2032) Battery Box Vector files to laser-cut a CR2032 holder with a sliding wood lock. The red outline is the lid which can be cut from acrylic or wood. All cutting materials should be cut from 1/8" (3.2 mm) sheets of wood or acrylic.
thingiverse
A simple holder for up to 6 remote controls. ... Designed to be cut from 5mm plywood.
thingiverse
Snap together business card holder for a Laser Cutter Forged at MakeWorks Coworking Studio in toronto. Check us out if you need access to prototyping tools, or need an awesomely fun place to make your startup happen. Print Settings Printer: Trotec...
cults3d
... forget that you would need an M4 nut to go with that. Designed in Autodesk Fusion 360. If you can tell from the pictures, the bolt slides though the slot in the handle to hold it very securely. Make sure that 5mm wood is used when laser cutting.
thingiverse
... forget that you would need an M4 nut to go with that. Designed in Autodesk Fusion 360. If you can tell from the pictures, the bolt slides though the slot in the handle to hold it very securely. Make sure that 5mm wood is used when laser cutting.
thingiverse
Instructions Cut the black parts from 3.8mm (most likely sold as "4mm") plywood or acrylic, glue the parts together (apply some glue to the rubber foam too in order to keep it in place when pulling out the cups) and attach it somewhere using some...
thingiverse
Sometimes you need a very basic file that will run quickly and still be interesting enough to hand out during an open house. ...This is a very basic headphone holder with room to engrave a logo. ...
thingiverse
A remix of Lifelix's candle holder. Trees was too thin so I did one and change the design of the other panel. ...I use Illustrator to vectorialize wolf and deer picture and add them to panel with Lasercut
thingiverse
# Multimeter hanger / holder If you wish to modify it yourself, link to drawings: https://cad.onshape.com/documents/1d5dd7bdbe8f57a2ac4b224e/w/4ca23e28a01b2540e0222d91/e/518aa863eb4a2ee0534eeeda Works with cheap DT-830 and similar multimeters. ...
thingiverse
We needed a basic phone holder to demonstrate for a class project, and when we couldn't find a pattern we made our own. The pictured design is from the British Library's flickr account and not included in the file. The phone pictured is...
cults3d
Pen holder for cutting plotter. Compatible with Silhouette and the most common ones like the King Rabbit in my case. I needed to make marks for die cuts in the cutting plotter and to avoid losing material what I do first is to diagram with the pen...
thingiverse
Laser cut. ... Plywood 4mm. Cut compensation: 0.15mm Napkin holder size: 222x158x50mm Napkin size 150x150mm
thingiverse
i ve created this pencil holder for those who are interested in laser cutting stuffs.
thingiverse
Laser-cut holder for 6 dumbbells - 2x 2lb, 2x 5lb, 2x 10lb. Sized to be cut from 5mm plywood. The profile for the dumbbell rack was designed in FreeCAD, and post-processed in inkscape. ... Both source files are included.