laser pointer holder 3d models

And for final protection, just screw the top onto that. I have included two top parts, which are for the Kit Lens of the olympus micro four thirds, the Zuiko 14-42, and for the zoom Zuiko 40-150. I included a bit wiggle room on top and sides, so you...

After 1 hour of adjustment, I achieved a precision of +/- 50um.\nI didn't write extensive documentation, but took plenty of photos during the build process.\nIf you have a basic understanding of how probes work, you'll be able to replicate this...

Print new probe holder I designed a probe holder with a channel down the side that would fit the thermistor, allowing me to get a pretty good guess as to the temperature of the probe. It's designed to fit into my modified BLTouch mount for the BMG...

Also, the prints include a blank label plate - you can stick a label on it or just write on it with a marker. The collet rack consists of these pieces : rack frame combination holder/label plate (snaps into the frame) clips to assemble the frames...

UPDATE: This works great, the roller is so smooth that I had to put a rubber band around the roller and holder. It's not tight but not loose, it fits without needing to be stretched. This was needed to act as a damper, when the extruder moved...

Other parts designed for my printers include: http://www.thingiverse.com/thing:1959901 (GT2 belt clamp (Prusa Y-axis)) http://www.thingiverse.com/thing:1937232 (Arduino Mega and RAMPS v1.4 case) http://www.thingiverse.com/thing:1905409 (Prusa i3...

Infill is set to 20% except for ring magnet holders, which have 50-100% infill due to their 1/8" set screw holes. The wire and pulse circuit configuration are left up to the user, with various options available. A suitable starting point could be a...

Another is a USB drive holder. These can be added to the print. If you want the hooks to be shorter, you can easily modify the STL file or sand it down. I would use glow in the dark filament This is because last night, I had an idea about a cable...

The spinner holder I put around the towel bar so that you can hold it while the bar spins and then use sandpaper or a file to taper the ends of the towel bar. Print Settings Printer Brand: Wanhao Printer: Duplicator9Rafts: No Supports: ...

Cliché holder with a diameter of 30mm (3cm) THE STL FILE INCLUDES: 1 Seal (80x40x20mm) 1 support for the clichés Immediate delivery via email WATCH VIDEO - https://www.instagram.com/p/CYhJkJlKyZy/ EXCLUSIVITY - I HAVE 3 MODEL OPTIONS: 1) POCKET...

To make inserting the USB drive on the side of the printer a bit easier, I bought a small 15cm USB extension cable which I then mounted in a small holder for the cable and attached it with 2 screw from the outside to the inside wall of the...

Years ago my son brought home an ingenious electric motor made of a coil of wire supported on brass contacts above a D cell battery holder. I thought it was quite an elegant little demonstration. I was recently asked if my company could support a...

Update: I updated the rollers due to problems with almost empty filament rolls; they aren't heavy enough and the friction just tops them off the holder. The new rollers are based on bearing idea I saw in Thingiverse some time ago. I didn't find the...

I used the 4 clips from the top of the case (be careful when removing) and placed them on each of the four clip holders on the tophat. You basically just need to slide them in sideways. Based on how your print turned out, you might need to use a...

This time, I made an Hex-Key holder that consists of two parts. I wanted to test the accuracy of the machine with these plastic brackets. It was good enough to make the two parts fit super tight. I just hammered them together and the connection is...

If a water stream passes a hole, it can create a pathway for the water to continue running out of the pot. Plants can be attached to the sides by inserting the holders into the three holes around the ouside of the pot, or just with rubber bands. It's...

If the turntable with a battery compartment, you can choose the turntable without battery compartment and attach a commercial battery holder to it, better suited to your project. Français : Cette station météo peut recevoir les capteurs de...

If bending proves too challenging, I will either swap the corner pieces with holders for 40mm tubes or add a second 25mm tube below - which is more complicated and less likely to happen. This alternative solution is already included in this upload. I...

The new pressure bar holder is longer to accommodate the spring. A new knob, M5 bolt, and 8mm x 20mm spring have been introduced. Note that the old bolt was an M6, which took up excessive space. The pressure bar has also been modified to...

I Recommend You Check Out My New Filament Spool Holder - No Spring The Claw Remake. Why This Model? I Needed a New Spoolholder For My Version Of "Ultimaker 2 Aluminum Extrusion 3D Printer" Http://Www.Thingiverse.Com/Thing:811271 And A Way To Mount...

In no event shall the authors or copyright holders be liable for any claim, damages, or other liability, whether in an action of contract, tort, or otherwise, arising from, out of, or in connection with the software or the use or other dealings in...

**Edit:** I have now made a holder for the agenda and act decks, which can be found at https://www.thingiverse.com/thing:2847702. This includes a version with a Doom Tray, made specifically for my doom tokens. ## Model-specific notes ### Horror...

Make your sky watcher goto + track for around $200A hybrid of many of the onstep projects but without having to cut a larger hole in the base of the sky-watcher.Parts needed:onstep board: in my case a fsyetc e4 - preprogrammed...

*E3_MPSU_Modular_Cover_USB-Mainv2.stl I used supports on the long bridge section above the wide opening, and the holders for the restraining screw braces that attach the part with the USB charger. I really doubt that the bridge section needed them,...

For your setup: the parts included per standard set *: * Paddle * Paddle Caps * Dispenser Cage * Extension Rings * Top Ring * Short legs (three of them in 1 STL file) * Cage Legs (seven in total) * Optional - a leg with a label holder Instructions...

I used a battery box sourced from Ebay, "1Pcs 10 AA 2A Battery 15V Clip Holder Box Case Storage w/6" Wire Leads Black". The cost was about £1.50, plus ten AA NiMH batteries. Alternatively, you can use a 12v PSU with a centre positive 5.5mm x 2.5mm DC...

But if you want to try a version that does not need the M3 inserts, I made a remix at the link below (which is the same design without the inserts - and is not tested): https://www.thingiverse.com/thing:3537261 If you need to mount the screen at an...

Amphibian CarBoat Creator [10] Thing URL: http://www.thingiverse.com/thing:932465 [10] Thing Author: MyMicrofactory Artist [10] Thing Licence: Creative Commons - Attribution - Share Alike Policy [11] Thing Title: Flashforge Dreamer Spool/ Filament...

UPD: Updated set of parts for printing the digital version of the ZOHD Dart 250g.List of changes:Revised FC mount for the latest revisions (FC needs to be glued with 3M double-sided tape).Revised camera mount.Added antenna holder.Flight video in 25...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.