lattice cube 3d print

The V1 frame weighs about 10g, while the V2 frame weighs around 8g when printed using PLA. My entire setup (currently based on the V2 base and the V1 top) weighs roughly 38g without the battery. It is specifically designed to support motors measuring...

If you're adding them then I'd recommend printing a few extra as I found the mount pins to be a bit fragile - they're only there to guide you when attaching them. Just a dab of superglue will hold the stack mounts in place. Exactly like the...

Print nose with supports everywhere and 20% support density. Also use 20% support density with support brim, support roof, and support towers enabled on the LID. Use four walls and 20% infill or more on the nose, and 40% on the LID. The lid also...

This is the same Bezel as #4 but without the printing between the buttons of the TFT. The portion of the case that goes over the Zero4U USB hub was not modified in any way. It can be found with the Original Zero4U case by ttocsneb. I have secured...

different clamping nut sizes.And this is the result of some drawing and printing.• Part 1 is the mounting plate suitable for all diameters of clamping nuts.       This is mounted on the tool-holder plate using the hole in the plate to secure and an...

I was constrained by the size of the rotary switch and the USB breakout board otherwise it might have gotten a bit smaller. See it in action: https://youtu.be/PTTVuVUZYM8 I have included the OpenSCAD file which is somewhat parametric. Print...

Files with FDM are modified to print better with filament printers Set 04 - Generals and Staff - FM Bluecher in several poses, plus a few generals and other staff officers Set 05 - Misc. Officers - Many Reserve and Landwehr officers wore regulation...

When I printed it, I placed the A blocks right next to the B blocks in the slicer, so they were already joined together. Here are the coordinates in case you want to get neighboring pieces, or need them for whatever reason. I'm also including...

Migrating from thingiversehttps://www.thingiverse.com/thing:4387788 Adapter to connect a removable 150mm flexible duck to a 250mm Ceiling Extractor to remove Solder / Flux fume.designed to be printed on a CR-10S PRO , so a 300X300 bed...

All necessary parts for a compact, three-dimensional printed mini tri copter modelled after RCExplorer V3 will need to be acquired. This endeavor relies heavily on David Windeståls impressive design and accomplishments. Those wishing to assist David...

Not only was it my first real model using FreeCAD - which I'm still learning - but it's also my very first attempt at designing printed screw threads. True to form, I didn't start with something simple where you just look up standard threads on a...

With S3D I can change my temperatures when I print from the machine control window, so I can use different filament using the same gcode. The base mounts the vertical coin holder base. The CR2032 holder is common. The fit is not real tight and you...

This can be printed with up to a 1mm nozzle. Quite the boon if you ask me. How to upgrade a pack: 1. Run wires (14/12 gauge depending how pedantic you are) down the pack to new rows of cells. This parallelizes those cells with the 5s pack that...

For the same price of one tent pole could buy 2 x 6.5m lengths of Al tube, and a roll of filament. Took a few attempts but the twist lock cams were very easy to design and print and worked far better than expected.  The larger version...

in die Hemdtasche stecken.(Sorry für alle die bis Mittags am 4.7.22 das Modell geladen haben da hat sich ein Flüchtigkeitsfehler eingeschlichen, Verbindung am Klipp, inzwischen korrigiert, noch zu sehen auf dem letzten Bild)Hier das Ursprüngliche...

A modular board design helps with capturing the fine details of original design, as larger individual tiles can be separately printed even on smaller beds; additionally, the tiles can be easily stored. Game Rules Each player takes a set of seven...

(I use 4 x 25mm M2 screws) For mountig my rx and vtx, i printed 1 x vtx_base.stl which fits onto the fc stack. For the rectangle standoffs you need 2 screws and 2 nuts to fix it. These standoffs are inteded to use at the left, right and rear side of...

The size works for the 5mm drop or default height, will need to print 2 of them (unless you go with a different cable relief setup, then you won't need them)..As for the x-axis mount, I made it so the endstop sits directly on the mount, and designed...

- Some nice, yellow PLA (I couldn't find an exact color match, but I got close!) - Revel Contacta glue - A hot glue gun - Some clamps - A soldering iron (with a small tip) & solder - A small, flat-head screwdriver - [Male & female USB C...

... had to be enlarged to be printable at this size. Resized to 1/3000 scale, the gun barrels and some other details are lost. Printing at larger scales is of course possible, though the lack of detail suited for 1/2400 will become more apparent.

Initially named the RR Donnelley Building after the printing company that served as its primary tenant, it later became the corporate headquarters of United Airlines in 2007 following a deal that included acquiring naming rights to the building. This...

********************Please add your print in Made directory***************** ********************Please Like <3***************** ********************Folow Me !!*****************...

Changes I made to existing models: * Removed cable tie bump things because they're unnecessary and just add to print time. * Added holes on the Raspberry Pi panel so you can zip-tie extra Z cables in a service loop. * Changed the PSU front panel to...

Use in place of magnets and glue both sidesCast a line out with a topper connectedConnect the body, and weight if desiredWait for bite indicationHook fish then pull the bottom off to reduce weight on the line when reeling inReel in, repeat Printed...

Generating Attributions log: [0] Thing Title : Cover for Flashlight [0] Thing URL : http://www.thingiverse.com/thing:882 [0] Thing Author : wizard23 [0] Thing Licence : Creative Commons - Attribution - Non-Commercial [1] Thing Title : Harmonic Drive...

I'm waiting until I have all of the parts printed for my new printer I'm building before installing this upgrade on my printer. When I do, I'll create detailed assembly and installation instructions. Here are some instructions if you want to try...

... my workflow and as long as nobody complains you are forced to do so too :P. But don't be afraid my friend 3mf is as simple to use as STL. PS: If you only need some protection for the camera u can just print one bumper and cap and you are set. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: pinNumberY = 35 pinNumberX = 13 GEAR GENERATION ON Music Cylinder Teeth Number = 24 Minimum Diameter = 1.5 inches Gap Between Gears = 1 inch...

Only disadvantage: Ender3 only has 200x200 to 220 to 200 mm print area. The arm is too long for this Maybe a friend has a bigger printer Here is my "all-round package" with 120, 135 and 140 degree holders for the common 2kg rolls. The original...

The same cable must then go to the component to be coated and be attached there with an alligator clip, for example, and finally be inserted into the ground with an earth hook or plugged into a socket with a printed plug with a metal pin on the...