lazy boy model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Theoretically, it can run more than 11 hours on 1 load (not tested). What parts do you need?Plastic parts:You can use the print files if you have an MK3S or you can use the model files and set everything up yourself. The photos show the position...

Print the first layers in white and the following layers in another color. UseOnce printed, put a Tesa PowerStrip onto the base and stick it on a surface.Other modelsAlso have a look at all my customizable creations. There are more...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers).For adjustable friction, I've added a simple bail that attaches to...

Update 2021/02/06: Upgraded parts- steering arm 2.0 Bump steer reduce for steering knuckle 2.0(the ackermann angle have been reduce on steering knuckle 2.0 and therefore with the change of geometry this part is required to reduce bump steer) Update...

Once you have the rights % size change, you can Meshmixer or TinkerCad any model onto the clip_in_insert to create all kinds of new experiences for your animals, or useful things such as a cover for a feeding area to prevent gunk from falling into...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

I used this 5/8" tall flat bellows available from McMaster Carr:https://www.mcmaster.com/1320K111/These bellows are made for this job and are resistant to oils, lubricants, and heat.The models are designed to fit an Eerie Tools SM-LTHM 7x14 lathe but...

...Please check if they are valid for your model.Choice & file prefixesABCDcap typeFXFXSFXEplainAAAbelt tensionBBBtyre inflationCDDall cap variants use the same gasketgasketGGGFitI have printed two dozens of variants during development of the caps.

I just have to choose a bulb of the wattage I want and with a high CRI to get the best image quality.Since Fresnel spotlights are a classic in the world of cinema, I based my project on a model of the Arri brand from the 1940s. Which has a spindle as...

SECOND NOTE: I made some corrections to the actual model after I printed it. I got my first attempt working, though it's not perfect. For example the shaft broke off while putting it together. I tried to make it a bit more robust, don't know if that...

For the extruder I used from: https://www.thingiverse.com/thing:2735475/files cable-holder.stl https://www.thingiverse.com/download:4650325 extruder-cover.stl https://www.thingiverse.com/download:4650320 extruder-idler.stl...

I added some build notes below and a BOM which doesn't include screws, wires, connectors, etc., but has all major components. I planned to revisit this model and release a better version. However I have at least a year's worth of projects in...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

If you want to be able to focus it, you'll need a helicoid that maintains or falls below M42's register distance of 47.46mm at its shortest for your camera setup. Disclaimer: This model is offered AS-IS with no guarantee that it will print for you as...

The solution is simple enough: Both parts of the model need to be placed away from the centre point (still properly lined up with one another, obviously), so that the probe can do its thing without the first print getting in the way. So began attempt...

The automatic transmission in some models has a tendency to fail prematurely. This usually happens around an average mileage of 108,000. **1.1 Identifying Transmission Issues** Transmission failure can be determined through comprehensive...

Both uploading and downloading a few dozen bricks is a pain :) However you can get all: STL.zip contains all the blocks I made so far STL-sets.zip include multiple brick sets for printing (difficult and not so often updated !) source.zip contains all...

If you use OpenSCAD, the model could be adjusted further refine the diameter of the internal air channel for your needs. Caution, because small changes in diameter produce big changes in airflow! Print Settings ========== The dimensions of...

* IMPORTANT - please note that i've not printed this version myself, but the CAD models check out and everything should fit together. If you find any issues please let me know in the comments. 9th January 2021: * Revised 'top.stl' - Remove...

----------------------------------------------- MATERIALS ------------------------------------------------------ - Raspberry Pi Model 3 B (This is what I used but really any micro-controller can work) - Breadboard - Mini-Breadboard - 10K Resistors...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

Bear Exxa 1.0 is available here: https://www.thingiverse.com/thing:4362586 IMPORTANT: The Bear X axis will currently limit you to what alternative extruder/tool options you can mount without creating an adapter plate as it is different than previous...

NOTE: Newest v2.0 of this model is now available - click here.NOTE: This is v1.1. If you were looking for v1.0 - click here. Note: As of Nov 16, 2023 — in addition to the earlier remix changes, today I added SVG files for engraving the plexiglas...

Happy soldering! Source Files This print was modelled in Onshape. You can access the source files from here:</p> <ul> <li><a...

The COMPLETE Svartwood Trolls bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Trolls comes in all size and varieties, and being one of the most ancient people, no one knows...

Wandering hour clocks have been around since the 1600s, but this one implements the concept in 3D printing!This example uses the case, dial pan, glass, and movement from an IKEA BONDIS, but the model could be scaled on the X/Y axes to fit almost any...