led stage spotlights 3d models
86877 3d models found related to led stage spotlights.cults3d
Update 16/4/2017 Chad_R made an addon to secure the LED in the cabinet: http://www.thingiverse.com/thing:2251960 I wanted spotlights for my 3D printer cabinet so I decided to draw stage-like spotlights in miniature. I use LED's from Hobbyking and...
thingiverse
Update 16/4/2017 Chad_R made an addon to secure the LED in the cabinet:http://www.thingiverse.com/thing:2251960 I wanted spotlights for my 3D printer cabinet so I decided to draw stage-like spotlights in miniature. I use LED's from Hobbyking and run...
thingiverse
This addon is for the Stage-Inspired LED Spotlight by Depronized.http://www.thingiverse.com/thing:2051738 I made this addon to secure the LED curcuitry in place and have it be locked in after the whole Spotlight has been glued together. Also wanted...
thingiverse
I really like the Spotlight Depronized created. I wanted an easy way to mount them and be able to remove if/when necessary. So I created a clip mount that has a couple screw holes so they can be mounted pretty much anywhere or used as a stand on a...
thingiverse
(22 mm) I used the project https://www.thingiverse.com/thing:2051738 And the project https://www.thingiverse.com/thing:2507787 The internal diameter of the flashlight was converted to 22 mm optics The hole of the lantern clamp for the screw is 2.5 mm...
thingiverse
Just a little clip-on round base for 'Stage-inspired LED Spotlight' by Depronized. ... https://www.thingiverse.com/thing:2051738
thingiverse
I wanted to fit a bright, addressable RGB LED inside and decided on the [Adafruit Pixie](https://www.adafruit.com/product/2741). I did a bit of extruding of the existing model for the back housing of the light to accommodate the Pixie and added a...
thingiverse
First off, I scaled it to 300% of the original size, allowing me to fit a full size 120V socket and LED bulb inside. I also slightly extended the short barrel to fit the maximum size of my printer. Next, I created a barrel extension. I did this for 2...
prusaprinters
First off, I scaled it to 300% of the original size, allowing me to fit a full size 120V socket and LED bulb inside. I also slightly extended the short barrel to fit the maximum size of my printer. Next, I created a barrel extension. I did this for 2...
thingiverse
Remix des Bühnenscheinwerfers als 4er Bar zur Nutzung mit einer einfachen Lichterkette
cults3d
Set of 2 types of led spotlights for offroad modeling. 1/24th scale Can be adjusted to any size you need. FOR PERSONAL AND NON-COMMERCIAL USE ONLY. ... Please do not sell this STL file; Please do not modify the 3d files and offer for sale;
thingiverse
I designed this to use 12V LED panel lights with dimensions of 44mm x 30mm I was inspired to create this floodlight by Depronized's Stage-inspired LED Spotlight - https://www.thingiverse.com/thing:2051738 Uses M3 screws to attach the arm.
grabcad
New LED A7 stage light for applications where a lot of light is in demand
thingiverse
Light Filter for the Stage-Inspired LED Spotlight (https://www.thingiverse.com/thing:2051738) **Must Be Printed at 0.050 Resolution with first layer set at 0.200** **Please check out the other Things I've created -...
cults3d
This is a simple clip for LEDs which come 4 very bright white on a small PC board for $1.99 from the following source, and quite possibly others: http://www.goldmine-elec-products.com/prodinfo.asp?number=G15554 4 of these bright LEDs clipped to the Z...
thingiverse
For some reason I didn't want to stick the LEDs onto my Z stage with sticky back. I wanted them to be easily removable for repair or replacement. So, rather than just stick them to some material that I attached to the z stage, I made this thing. ...
pinshape
SummaryFor some reason I didn't want to stick the LEDs onto my Z stage with sticky back. I wanted them to be easily removable for repair or replacement. So, rather than just stick them to some material that I attached to the z stage, I made this...
thingiverse
This is a simple clip for LEDs which come 4 very bright white on a small PC board for $1.99 from the following source, and quite possibly others: http://www.goldmine-elec-products.com/prodinfo.asp?number=G15554 4 of these bright LEDs clipped to the Z...
cults3d
TODO: Modify the relevant parts from AzzA's Z Braces to add positionable light bars at the front and rear of the bed frame Add a variant of led_rail.stl that can hold a filament filter in some way Design a control box to allow each strip to be...
thingiverse
TODO: Modify the relevant parts from AzzA's Z Braces to add positionable light bars at the front and rear of the bed frame Add a variant of led_rail.stl that can hold a filament filter in some way Design a control box to allow each strip to be turned...
thingiverse
... using openscad and printed with black ABS. I had to cut the strings out of the LED holes. Instructions Print these out and glue in 10mm LEDs using a flexible adhesive or hot melt. ...Wire them to the 12V supply with current limiting resistors.
cults3d
USB Cord from my local Dollar Tree Leds, Heatsinks, and Magnets (3mmx2mm) from Amazon m3x16 screws and nuts from hardware store https://www.amazon.com/gp/product/B01DBZJAUG/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1...
thingiverse
USB Cord from my local Dollar Tree Leds, Heatsinks, and Magnets (3mmx2mm) from Amazon m3x16 screws and nuts from hardware store https://www.amazon.com/gp/product/B01DBZJAUG/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1...
cgtrader
A great looking stage spotlight with stand( to scale), well optimized topology for high detail but medium poly count,** best used with Blender** the blend scene comes with the blender spotlight parented to the mesh for easy moving and directing, and...
thingiverse
I used some LEDs from an old set of Christmas lights and added little holders to space 3 LEDs evenly in the light. I also changed out the brackets for more sturdy ones. The base fits onto an Ender 3 plate. ... To illuminate it you'll need a 3AA...