line cad 3d models

After that, thread the wires through the hole on the back of the enclosure, then insert the front of the module, ANGLE DOWN, so the USB port lines up with the hole on the front of the enclosure. You might need to use a small flat head screwdriver to...

* Layer: 0.2 * Material: PLA * Temp: 200C * Bed: 60C The mesh under clips part is a raft, but with reduced number of layers and increased spacing: * raft extra margin: 4 * raft top layers: 1 * raft top spacing: 1.2 * raft middle thickness: 0.2 *...

Cut the desired utensil like seen by the red line in image 3, this shape allows the stabilizer to swing better, keeping food on it.5. Glue the desired utensil into the “spoon attachment” with food-safe super glue. Let the glue dry for about an...

The fins are tall skinny things and many printers will have trouble printing them without producing wobbly lines in them. For this reason I've included "supported" fins which have adjacent towers that are connected to the fins by 1mm posts. Use...

Both main body and locking plate may brake along layer lines about 6-7 mm from their respective fronts. It takes a good effort to get there, but keep that in mind, Broken locking plate might make it difficult to disassemble the whole thing. ...I...

They are added this way for reliability and readability under Python..Install Audio Hat Drivers for MIC ULTRA+:git clone https://github.com/RASPIAUDIO/ultra2cd ultra2sudo ./install.shsudo rebootInstall and Configure Raspotify:Follow the guide at...

Parts are designed for 0.2mm layer, 0.4mm line width. **PART LIST** In addition to the 3D printed parts (2 caps, 2 plugs, 1 socket, 1 knob, 1 anchor), you will need: 3 - 1/4"-20 nuts 2 - 1/4-20 x 1" long socket cap screws 1 - 1/4"-20 x 3"...

I made the following changes: The sides are beveled outward at 2 degrees, which means when the template is on its side, it is angled 2 degrees so the drill hole lines up with the drill bit at 90 degrees. There is also a recess in 2 degrees in the...

It can be used to find the right settings for the extrusion factor to get the right wall thickness.It is designed with a 0.86 mm wall thickness to meet the default prusa slicer settings.Only 12 minutes print and 1,22 g.  Instructionprint the...

Now Cura will pick up the supports even if it's setup to the default 0.4mm line width V6 - Numerous edits *Limit switch mount lowered by 1mm to avoid the screws rubbing the belt, this corrects a problem with the standard Wanhao setup *The 4 x...

Leave around 2 cm (1 inch) space to the cut line. Shrink it. Cut the cable. Now the textile cable will not unravel since the heat shrink tube will hold it together. Attach the textile cable to the contacts of the lamp socket and assemble it according...

Printing Notes ----------------------------------------------------- For top left I printed the lettering and the lines next to the letters in a different color but that is by no means required. I used the pause at layer (one of the post processing...

The slide and carrier are meant to print upright, all this should be able to print flat, no supports, and if you're still playing with settings it should still be workable - the slide and carrier are very tight on purpose, the layer lines will bind...

Additionally, I wanted to put the coins in one long line, with all the cards behind. I find this makes it much easier to take in where each value coin is and what coins have already been taken during the game. During the design I had the idea that...

With a minimalist aesthetic, the Solo Tube Ceiling Lamp is perfect for those who appreciate clean lines and simple elegance. Measuring 24 inches long by 4 inches wide, this lamp is designed to fit seamlessly into any decor. The compact size makes it...

Planing on adding more extensions to make this a real filament extrusion line. /////////////////////// Thanks to @Sapienz for the original design. I remixed it to use more common hardware in the 3d printing world and also lowered the part count. Made...

Park space area designation separated for parks usage Agricultural categorized zones (categorized lands to utilize resource distribution more effectively) and a wide category grouping for industry types used for infrastructure mapping Nature details...

You insert the inter tube into the outer tube from the end, going in a straight line directly to the bottom, and then doing a half turn to lock the inter tube to the bottom of the outer tube. This avoids having to work the maze once just to get the...

Only the hood need supports to print, it must be printed on it’s “L” side so that the walls lines will be in the direction that will make the part the strongest. List of materials: -Some Dupont cables and pin’s to connect everything. -DC 2.1mm...

Remove the rubber surface on the turntable and line up the six holes with the screws underneath. Remove these screws with a magnetic screwdriver. Remove the three black screws at the rear Remove the two screws at the front of the top (just above...

Quality layer height: 0.2 Shell wall line count: 8 top layers: 8 bottom layers: 8 Infill Infill density 40% (the upper is better done in 100%) infill pattern: cubic support generate support: Yes Build plate adhesion build plate adhesion type: Brim...

This attractive keychain-sized marble maze prints quickly with no supports, and the only hardware needed is a ball bearing - best of all, the ball cannot fall out, so you can take it with you to keep you occupied while waiting in lines, or play with...

Adjust your clock correctly and wait for 24 hours, then Measure the error of your clock in seconds.Input the error value (in second) for the value named COMPENSATION_SECONDS at line #3 in the source code. If your clock gains (too fast), enter...

Some additional notes on lighting (update as of 3/16/2015): I lined the interior of the box with aluminum foil tape (usually found at hardware stores in the plumbing section). This makes the interior reflective. You can also paint the inside white...

It's more stuff to rattle behind the dashboard, provides more opportunity for dirty contacts, and adds the potential for it to vibrate undone at some point down the line. If you want to fit an aftermarket stereo to a Swift, you'll need a custom...

(Don't confuse these with the incompatible Minolta autofocus lens mount, A, which began with the Maxxum line in 1985 and has been continued by Sony since 2006.) Because SR has a relatively short flange distance, there were not many adapters to mount...

In designing the figures, students use skills related to intersecting lines, planes, and angles. Finally, students got to try using Mathematica and 3D printing software. Audience I assigned this project to my multivariable calculus class. The...

Use peg arm if want to add pegs to line up with arm armor. Arm armor change to allow pegs. I can't do any testing at this time. Waiting to get more supplies. Hopefully be able to do some more testing on 6/10. I have one more request to work on...

Using this formula will ensure that the claws will be printed with consistent lines for optimal strength.A good value for the number of shells depends on the size of the tool. For small tools like 5mm diameter i go with 3 shells. For 10mm diameter...

I was able to get things lined up pretty well, and both sides are about the same – less than 25 oz/in to move them, that's with the motor attached. I must admit I was worried about lost steps in the Z axis so I built a little indicator for the right...