logitech g920 shifter sequential mod 3d models

It features: - absolute supportfree printing - mod-ability to some extend due to granular parts (some template-parts already included, more to come) and freecad-sketches - no glueing anywhere - only 3 different screwsizes + nuts needed (M2x8, M3x8,...

Risers You'll need your printer at least 30mm off the ground for proper clearance with these mods. For that purpose, I've created a couple of different riser/feet options: This one uses the stock rubber...

All printers tolerances are slightly different in my experienceImprovements/Tweaks I've MadeWider spine, so film is held betterResized the overall reel width so the film holds properlyOpened up the outer-most sprockets/lengths of the reel (they were...

... Unless you are using transparent filament this is not a necessity. The base is the functional part of this set. Printing one pair at 0.30mm layer height will take about 23m Here's an example video of putting the tea light mod together:

Mods to above: * Nothing's changed with the X-Carriage. * Nimble mount: I mirrored the part where the Nimble attaches to so I could mount it on my current X-Carriage. This meant adding three holes for screws, and I also added flanges on the bottom...

Requires My Part Fan Shroud Mod: http://www.thingiverse.com/thing:1792867 to Move the Fans Up and In to Clear the Sides of the Enclosure. To Complete This, You Will Need: * 20 x 1/4-20x3/4" Bolts * 20 x 1/4-20 Nyloc Nuts * 12 #8x3/8" Sheet Metal...

This case is designed for Nixie clocks with top-view tubes, but can easily be modded to accommodate other displays and controls. It is inspired by the lovely midcentury design of the Italy-made <a...

It looks cool, though (thanks to #Geoffro 's awesome model https://www.thingiverse.com/thing:500093 ) and the mouth should glow since I added a tube there.\r\n\r\nIf you don't see what you want, check out the Remixes:\r\n* Dingoboy71's:...

Please feel free to print, mod and share your builds with the hashtag #NLR35.NLR35's key features are:- 2 camera mounting options- analog or digital FPV link- ELRS long range RC link- 1s 12A AIO board- top or bottom battery mounting- push or pull...

This mod is destructive, meaning you'll be drilling holes in the controller, voiding the warranty and if not careful, damaging it. With this adapter, you can use GoPro-related extensions to mount whatever you want such as a GoPro or reposition the...

However, I changed a various things and thats why I publish this mod. My modifications: - I created a new cover because the original one cover was not fitting, - The original rover's cam mount was made for that whoop AIO nano cams and image was...

Shopping list in addition to re-used parts. Rails... 2x MGN12 330mm Rail 2x MGN12C Cartridge 1x MGN12H Cartridge 22x M3 12mm Socket Head bolt (6 are used for the guides) 10x M3 3030 T Nut (6 are used for the guides) Y Belt System 1 GT2 20T 5mm...

&nbsp;Only needed because I am printing in heated chamber, which caused a bit of flex on the normal bracket.Modded L and R Ducts again. I am printing ABS in a 50C chamber and the thin ducts kept melting, even when printed in ABS (transparent). Pics...

(Print "FrontPanel_input_noSCART" instead of "FrontPanel_input") If you connect Component or VGA, you can use a SCART breakout to pass through audio in a clean way, without ever having to swap the plug on the back. Last, you'll need 8mm M3 hex bolts,...

Cooling_Fan_Toolhead_CAN_Board This MOD arises from the need for active cooling on the Toolhead Board CAN for VORON2.4 350 Afterburner with cable chain. When printing ABS or other materials, with the doors closed the Toolhead Board CAN reaches...

Will work with most other mods! You can see the [CR Series Y Axis Screw here](https://www.thingiverse.com/thing:4039877) and the [CR Series Octoprint ready SKR conversion here](https://www.thingiverse.com/thing:4130769). #[Come hang out get...

- The X axis turns out to be a bit difficult because things look bigger in CAD than they really are :/ - The distance between the two X rods is only 27mm, yes, 2.7cm, not alot, I think the Anet A8 has around 40mm between the two rods which means that...

Post-Printing: Check the clearance between the belt and the block How I Designed This: Although I've been using the printer for more than a year, I only realized that the belt was rubbing against the housing several months later, after I saw a video...

INSTALLATION INSTRUCTIONS This might vary if you have done mods already. Start by removing filaments and cables. Cool down the print head after filament removal. Remove the four retaining screws on the right-hand side of the extruder that...

I've wanted to make a 'crystal reveal' lightsaber for some time, so while working on mods for the Anakin saber, I came up with a crystal chamber design that's revealed when the saber is pulled open. I'm no engineer so I did my best to make a sliding...

I am including the SketchUp file in case it helps someone with mods.&nbsp;My PayPal tip jar: https://paypal.me/design8studio &nbsp;&nbsp;Various LowRider 3 CNC remixes:LowRider 3 CNC Collection&nbsp;View all my models and remixes on...

Vous pouvez l'imprimer en ABS ou PETG sans problèmes si vous le voulez.2 fois moins bruyant que l'origine.Aussi performant que l'origine.Sans modification de l'emplacement de la tête d'impression et du capteur de nivellement BL-Touch !Maintenance...

Primarily designed for my Zaribo-modded Prusa i3 MK3S, but I adapted the design for 2020 extrusions as well (for my Alfawise U20), and for a friend's request I made a tabletop version. You'll need four 608 bearings as well.</p> <p>The holes are sized...

A new variation, similar to the 4mm dowel approach, is with the carrier modded for 2mm cap head screws (12mm long). A counter-sink area allows the cap end to be screwed flush to the carrier surface. The same 4mm OD 2mm ID stainless tubing is used to...

Consider my related mod: http://www.thingiverse.com/thing:2090159 This really belongs on Instructables.com but I didn't want it to get lost there. The STL file is of layer 4, the one I modified. I haven't printed the STL file or tested it for fit. I...

I printed them on my modded direct-drive CR-10 with a 0.8 mm volcano nozzle and 0.4 mm layer heights. You can probably use your normal slicer settings, I just wanted to cut down on print time as much as possible. No brim needed, 100% infill.</p>...

Many of the changes are already included upstream but have not yet made it to Alex's fork.Some links to the info required.Cable mod &amp; firmware changes - https://github.com/MarlinFirmware/Configurations/issues/535More required firmware changes -...

If you're into modding, a stock blaster catch/trigger/lock spring could also do the trick provided it's the right length. More detailed instructions are included in the README.txt file. Enjoy the build, and happy foam-flinging. If anyone gets...

It works but is a bit of a pain to fit, would do it differently next time but I wanted to keep the bottom as flat as possible and with good ground clearance. I used a large allen key through the holes in the bottom of the motor shield parts to align...

Even better cooling is being developed and a few other mods to improve endurance over longer distances. Water cooled esc's are easy off the shelf for model boats etc and I may build enough space for a cheap (solar fountain type) water pump in the...