magnus style fidget spinner by 3d models

So they are a little small (but not by much) To use: A) Take the axle Place a hub on it. B) Place the spool on next. C) Place the other hub on the axle. D) Use the clips to keep the hubs snug against the spool. E) Place the axle on the...

This reduces the filament path length by 9.6 mm and means you do not need to swap ducts or move the probe when changing between Rapido UHF and Dragon or other E3D V6 length hot ends. <b>Probe mounts:<b> 8 mm inductive Bltouch Euclid Please...

I also found that my glass plate was being warped by the clamps, wires, and aluminum foil. Corrections. I flipped the heating bed over (not how any pictures I have seen from Geeetech). Then I made some great glass clips. Kudos to the author (I'll...

If you are lowering that corner, and the top line goes up, you went to far, so raise that corner by 0.05 degrees 3. Then do the Y direction in the same way. The dual and triple spacers are my design. The single is a remix of 5473587. Printed...

However it is possible to just use two, three or four colors by using the cube as an insert. Please read the printing instructions below before starting, as there is some manual labor involved.Two Color VersionPrint the cube model first. Print the...

Yosemite Sam, a cartoon character in the Looney Tunes and Merrie Melodies series of short films produced by Warner Bros. He is commonly depicted as an extremely aggressive, gunslinging outlaw or cowboy with a hair-trigger temper and an intense...

I found the designs by @wslab and my wife chose Black Cat 10. I downloaded the .stl and was able to hack it in FreeCAD (basically traced it into a sketch) to 5mm thick extrusion, "CLEAN" and "DIRTY" text strings (using Arial Black) cut 2mm out of the...

Functionality: A tube is placed in the holder and then rotated by hand. The tool deburrs the applied edge (inside or outside). Tool: For plastic I use Dremel 3mm wood router bits. Here especially a radius cutter, because then there are no...

 However, I soon realised that the most significant limitation wasn’t the lenses or my adaptors but restrictions set by optics. For example, the closer you are to your subject, the smaller the depth of field (the region in focus). Macro photography...

... and [Instagram](https://www.instagram.com/nhmwien/) (nhmwien). The cookie cutter designs are partly based on 3D models from our [3D museum](http://sketchfab.com/NHMWien) and were designed by Viola Winkler. ...

I find the value offered by http://dangerousprototypes.com/store/pcbs particularly appealing, especially for a board of this size. Print Settings: Supports: Yes Resolution: 0.15mm Infill: 30% Notes: All 3D printed parts are printed in ABS with a 30%...

(Cat 1 Mammoth truck cab SOLD SEPARATELY) The internal volume is currently in our range, by far the largest. This means there’s more space for supplies and luxury, for those extra long expedition trips. The Cat 1 Mammoth body can be found here:...

https://www.thingiverse.com/thing:2201645 ____________________________________________________________________ Additional Links The idea was inspired by this video:...

I countersunk the screw heads on the cold end fan by drilling out, the cold end fan can be pushed through the component cooler. M3x20 screws with nuts are required for the 5015 fans. The limit switch holders are fastened with an M4x6 screw and a...

by pakkko English: I made a remix of this BLTouch holder because I had ordered a CR-Touch. I also wanted to keep the original hotend cover and not make any size losses on the bed. Yes, and now this holder for a <a...

NOTE: I printed the LED light panels AND the light diffuser panel in PETG just to help with the heat generated by the LEDs, although they just get a little warm, not that hot. I recommend that you start with the LED light panel that holds TWO...

This allows you to swap outlets (or put a cap in for winter), and minimizes the risk of damaging the main body.Easy access for maintenance by unscrewing the outlet connector.Internal drainage hole to direct water down and out instead of through the...

it was found by experiments that at accelerations of 170-200, the motors pull them out at a maximum at a voltage of 1.2v and then nothing will help them. therefore, at accelerations up to 170, you can set 1.1v. After 1.5 kg of plastic, the native...

A durable body designed by me for the TAMIYA DT03 chassis. The bodywork consists of many elements that fit together perfectly. To assemble the body, you need to use screws and nuts. To assemble the body, glue must be used in some places. To assemble...

Links to other models: (Coming soon) Confirmed phone list for CanStandYa model A: LG G5 Would like to confirm CanStandYa model A for the following phones: (All phone models other than what's on the confirmed list) Patent Pending Disclaimer - Not...

Small benchtop 3a power supply easily created by printing on a Monoprice Select Mini. Bill of Materials: B10K potentiometer XL2001-5V USB buck converter DNS-VC288 voltmeter/anmeter LED display 3A LM2596 buck converter Male Power Socket with Fuse...

Load the switch from behind, then screw the switch to the mount by aligning the slots with tapped holes in switch. You could also cut a large rectangular hole to fit your switch body and load the switch from the top using hot glue on back side. ...

Holding them by hand for a layer or two until they're captive might also work fine. ...I rarely need to but somehow this time I had to use some glue stick to get good adhesion on the Prusa satin sheet.</p><h4>Actual instructions:</h4><ol><li>Print the...

Traditions set forth by those that came before them is that they could not directly intervene until the slate must be wiped clean again. After numerous millenia,  the Anteokheia will return to bring about the end of an era and civilizations. In...

I don't have step-by-step directions, but I've provided several photos and will attempt to provide helpful descriptions on assembly. Once you print things out, they should become clear to you as to where the parts go together. On the frame pieces...

One fan or two, I prefer two for better airflow.\r\n\r\nDon't forget: your warranty will be void by doing this mod.\r\n\r\nI had already put some 60mm noctua fans in my control box (to replace the 50 and 40mm), cut all the crap in front of the fans,...

How to build : This should be very simple, the hardest part is, by far, cutting the panels. 1) print everything (you can try to make one panel first to test the tolerance regarding your settings) 2) M3 tap the 4 hinges 3) M4 tap the 8 holes on...

It was created by taking the Duet DXF and then altering the mounting holes. I CNC routed mine from 3mm black acrylic using a Lowrider 2. Also suitable for laser cutting. Edit: DXF now included, I have no idea how that happened! The cable tie and...

I just lifted it up here to get a better picture) Testing:to test I would recommend printing several and running them side by side to compare the results and don't forget to post your results. Results:so far I have had really good results with all...

BONUS: You can use this as a "mini" gun stock by simply changing the mount for your dominant hand and using the front pipe! Other gunstocks in the market are super hard to use and can take weeks to learn. That is why we made our magnetic rifle...