maker select plus 3d printer cura

... ...Remove the tabs where the PCB is mounted after printing. An update with a cover will be added soon. Print Settings Printer: Monoprice Maker Select Plus Rafts: They don't matter. Supports: There are none. ... Resolution: It's 0.2 mm.

I designed a tool holder for the Monoprice Maker Select Plus (it may work on other 3D printers too). This tool holder keeps the included scraper, allen wrenches, PTFE tube, and nozzle cleaning tools all in one place. It also comes with an extra hook...

I'm struggling with the screws that hold my hotend fan in place on my Maker Select Plus / Wanhao Duplicator Plus. They're apparently M3 x 37MM, but I couldn't track any down, so I grabbed some standard M3 x 40MM bolts instead and created a spacer to...

For the Monoprice Maker Select Plus and Wanhao Duplicator i3 Plus: This mount relocates the PCB for all hotend components out of the way, freeing up the carriage block to accommodate alternate fan coolers while retaining all stock hardware. ***VERY...

I printed mine in 0.1mm layer heights but 0.2mm should be more than enough. Since the Wanhao Duplicator i3 Plus/Monoprice Maker Select Plus are 24V native printers you need to make sure you wire the LED panels in SERIES so that each panel will only...

As Wanhao Duplicator i3 Plus/Monoprice Maker Select Plus printers are native 24V machines, wire the LED panels in series to ensure each panel receives only 12V of power. The light panels I used are available on Amazon at...

I was less than satisfied with the standard Y idler bracket on my Monoprice Select Maker Plus, so I set out to create a better one. This custom design leverages the stock two mounting holes, but also demands an additional hole drilled precisely into...

I upgraded my Maker Select Plus with a CiiiCooler, but that required swapping in a 40mm fan adapter since I couldn't find a stock fan replacement. Unfortunately, even with the adapter installed, the PCB holder I purchased wouldn't fit within the...

The original holder is no longer sufficient to support multiple filament spools on top of the Wanhao I3 Plus or its clones, prompting a need for an upgrade.

Additional parts required to be printed: https://www.thingiverse.com/thing:1394558 qty 1 https://www.thingiverse.com/download:3442143 qty 2 Note: The stops linked are for the 2.1, not the plus, which has a different mount for the y stop, thus the 2...

... inspired by the original Raspberry Pi Camera v2 Print Bed Mount created by jlarsenwy. ...It features an extended arm, allowing for more flexibility in positioning the camera, and includes a dedicated component for securing it to the printer's frame.

... driver. ...The guide slot for the BLTouch ribbon cable is also slightly deeper in this revised design. Almost certainly, a shim will be needed - scale the 3mm model up or down as required in Z (for my printer, it was necessary to increase by 3.4mm).

Leveling my printer was a breeze thanks to the screw-in feet, so I merged that feature with the rear feet from this design: https://www.thingiverse.com/thing:2349318. To assemble the lower brace, you'll need longer M5 bolts, and for the top brace,...

... You may do whatever you want with this model - edit it, repost it, sell it, etc. - as long as I receive proper credit for it. Print Settings: Printer: Maker Select 3D Printer v2 Rafts: Doesn't Matter Supports: No Resolution: 0.2 mm Infill: 40%

Spool Supports for MP Maker Select 3D Printer v2 (and Prusa Mendel i3 3D Printers) The U/T bracket fits over the printer's frame to prevent sliding forward and backward. It fits snugly into a 1" PVC pipe, as seen in the printed examples. I use...

Filament Feed Spool Brackets for MP Maker Select 3D Printer v2 - A Simple Solution with Two Parts to Print. To assemble this design, you'll need two 75mm long half-inch PVC pipes, two 150mm long half-inch PVC pipes, two 350mm long half-inch PVC...

Most standard lighting mods attach to the frame which is not an ideal angle for the light and can shine right in your eyes if you sit next to the printer like I do. So, I designed these to mount securely to the 8mm z-axis brace rods. Features: - ...

I adapted this snap case to enable secure attachment of the case to my Monoprice Maker Select Plus/Wanhao i3 Plus 3D printer.

I recently upgraded to an MKS Gen L V1.0 controller on my Maker Select Plus/Duplicator i3 Plus 3D printer, switching out the failed main control board for this more affordable option.

A modification of tritiumfusion's version of the Wanhao i3 Plus Pulley Stabilizer, except made to work with the stock hardware that the Monoprice Maker Select Plus comes with. ... Category: 3D Printer Parts

This a filament guide for Monoprice Maker Select Plus. ...That requires No screws for attachment.

It's amazing how it seamlessly integrates with the Monoprice Maker Select Plus, as well as other printers that share similar capabilities. ...Kudos are in order for AnansiTheArmadillidiidae and his outstanding "Maker Select Filament Guide" - a true...

Allows the mounting of multiple styles of IP Cameras (YI, Foscam etc) on the boom and will swing out of the way when you need to work on the machine. The bottom two screw holes are meant to fit snugly over the bottom screw heads for support so you...

Vibration Absorbing Feet for Monoprice Maker Select Plus and Wanhaos i3 Plus. For each corner, you'll print two discs and position a sorbothane pad between them, ensuring the slot in the disc faces upwards. Place one under each corner of the frame,...

The Monoprice Maker Select Plus 3D printer lacks on-board lighting. To address this issue, simply attach these snap-on light fixtures to hold affordable 12V LED panels. You'll enjoy improved visibility of your prints in progress and better lighting...

These corner brackets secure a magnetic flex steel build plate in its place on the Monoprice Maker Select Plus printer. Most magnetic flex steel build plate modifications necessitate some type of clip that gets in the way of printing if you've...

This provides a way to attach an inductive bed probe to the Monoprice Maker Select Plus / Wanhao Duplicator i3 Plus printer. It's assumed that you have already installed a part cooling solution, which frees up the mounting point for the front...

Converted my Maker Select Plus to a RAMPS install, unfortunately this required a new LCD. ...I went with the RepRap Full Graphics Smart Controller. Printed the case here: http://www.thingiverse.com/thing:87250 Unfortunately I needed to mount it, so I...

... filament guide's circle. You can find it in vers. 3. In v4 I did a little cosmetic change. Print Settings Printer Brand: Monoprice Printer: Maker Select Plus Rafts: No Supports: No Resolution: 0.3mm Infill: 30% Filament: 3D Warhorse PLA black

I finally found this object https://www.thingiverse.com/thing:3550741 but it wasn't suitable for my printer model, a Monoprice Maker Select Plus, so I decided to start a project on Tinkercad and, inspired by the aforementioned object and starting...