maker select plus 3d printer cura

The frame fits perfectly on the Wanhao I3 Plus or Maker Select I3 Plus, and also likely works with the Select V2 series. This allows users to mount multiple styles of IP cameras (like YI and Foscam) onto the boom, which can swing out of the way when...

This webcam mount is crafted specifically for use with my Creative Live HD webcam, allowing it to be securely fastened to the bed of my Monoprice Maker Select Plus. So far, it's working seamlessly and I attach the pieces using M3 nuts and bolts. When...

There is a brand-new version of this thing available online:\r\nhttps://www.thingiverse.com/thing:3545762\r\n\r\n-------------------------------------------------------------------\r\n\r\nA Custom Filament Holder for Monoprice Maker Select Plus and...

I sought a solution to attach my Raspberry Pi 3 case running OctoPi to my Maker Select Plus printer in a way that kept it out of sight. To secure the Raspberry Pi case in the back, use two zip ties. This will ensure the case stays put while...

I swapped out the motherboard on my MP Maker Select Plus after it gave up the ghost. I upgraded to the BIGTREETECH SKR 1.4 Turbo + TFT35 LCD package. This brought some tough issues, including mounting both components to the printer. For the...

I'm replacing the Monoprice Maker Select Plus upper fan cover with an improved air diversion system. Unfortunately, I encountered some issues with the original design - it didn't quite fit, which caused a print failure and damaged a few fan blades.

The Monoprice Maker Select Plus and Wanahao i3 Plus filament holder attaches directly to the stock bracket located at the top of the machine, reducing rolling resistance significantly. This design allows for adjustable end stop widths and upright...

I recently purchased the MP Maker Select Plus printer and after only a week, I encountered an issue with the SD card slot. When trying to insert the SD card, it fails to "click" into place, but if I gently push it in by hand, the printer can read the...

After printing Berky93's Tool Holder for my Monoprice Select Plus, I decided to design a tool holder of my own to complement it perfectly on the other side. This tool holder holds all the tools I commonly use with my printer, including the nozzle...

Possibly my first big construction project, this cabinet is built to hold my Monoprice Maker Select V2 3D printer and two regular printers below it. I used multiple references to design my own version with input from many different sources and some...

*I've revised the corners to fit, and they're now ready to be posted.* The Wanhao file had some issues with tiny gaps that didn't align well with my Monoprice Plus printer. ...I made adjustments to the design and created a new corner piece that fits...

... To get the threads to print properly, I suggest you print thin layers and print them slow with lots of cooling. It is designed for the Wanhao Duplicator i3 Plus but should work on all the other re-brands of this printer, as far as I am aware.

I'm on my fifth Monoprice Maker Select and the bed leveling is still a challenge. The z stop always seems to be out of alignment, forcing me to back off the screws so far they almost fall off. So, I decided to use an insulated washer and add a 0.1...

remake to fit M8 Nut and bolt, and cut up some old mouse mat to make some rubber fit. ...all the pieces can be found here: https://www.thingiverse.com/thing:921948 Category: 3D Printer Accessories

Prototype Y and Z Limit Switch Bracket: A Quick Fix Using Spare Components I swapped out my limit switch bracket's original material for glass plus PEEK, necessitating an on-the-fly adjustment method to fine-tune the distances. To resolve this, I...

This is a sleeve case combined with a mounting plate to fit on the right side of the printer.

This is a versatile attachment that combines a protective sleeve and a sturdy mounting plate, designed specifically to be mounted securely on the right-hand side of your printer.

I discovered some LED strips that could be wrapped around the edge of the printer frame, but the problem arose because the frame was too thin to securely hold the LEDs flat. There are two files - print one for the top and two for the sides. You...

... degrees because the fan has to be slanted when mounted --- because the nozzle is not centered and is actually on the left side of the bearing block. The fan for this duct will still be the normal stock fan that should have come with your printer.

I wanted to install a fan duct that attaches through the rear side of the printer. The PCB was connected to one of the lower bearing blocks, so it had to be relocated. Ideally, it would sit higher but still be accessible even with short wiring...

... was created using Tinkercad's intuitive design platform. ...You can easily edit and customize it by visiting the official website at www.tinkercad.com, where you'll find a wide range of tools and features to help you bring your ideas to life in 3D.

Remove the screws from your printer 4. Loosely connect the upper and lower parts with the rods 5. Connect the parts to the printer 6. Tighten all the screws By the way, some of my pictures are early versions of prints (before I fixed slight defects...

EDIT: If this mount is too high for your printer, add two new shims (2mm & 3mm) with matching mounting holes. Print these and sandwich them between the mount and the metal part. ...You can also scale the Z in your slicer for a different thickness shim.

I designed this project specifically for my Monoprice Maker Select printer, but it has potential applications in various settings. With this setup, I can easily switch between printing on the build tek surface and glass while ensuring the nozzle...

This bracket attaches securely to the frame of a Monoprice Maker Select V2 or any other printer featuring four 3mm bolts spaced 30mm apart, and gives you total control over your phone's power button and charging port while keeping them safe from...

A grid pattern print is also included to help you verify that your height settings are accurate for your Monoprice Maker Select Plus printer. ... Print Settings: Printer: Monoprice Maker Select Plus Rafts: No Supports: No Resolution: 200 microns...

I recently upgraded my Monoprice Maker Select Plus 3D printer (rebranded Wanhao Duplicator i3 Plus) to Octoprint, which includes the option to add a webcam for print monitoring. ...Then I drew up a simple printable mount for a Logitech c270 webcam.

Clips on the top of the frame Print Settings Printer Brand: Monoprice Printer: Maker Select Plus Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20% Filament: Zyltech PLA green Notes: Print with model orientation, add supports for the top ball. I...

... for each side, with a zip tie on the bottom of each to help prevent wire tug. Print Settings Printer: Rafts: No Supports: No Resolution: .2 Infill: 60% Notes: 3 shells, 4 bottom layers, 4 top layers. ...Print flat to minimize z banding and wobble.

You will also need to print any one of the case tops from the original pi4 model here or original pi3b+ model here. The OpenSCAD source used to add the holes is also attached, so the mounting points can be customized if desired. Print Settings...