maker select plus 3d printer cura

The original design was tweaked to accommodate a mounting bolt that had shifted a few millimeters from its intended position.

Modified the base model of the Prusa i3 camera mount in Fusion 360, customizing it to perfectly fit the horizontal gantry of the Monoprice Maker Select Plus. ...The modified design securely clips onto the top frame.

Added mounting holes to [@Malolo's screw-less / snap fit Raspberry Pi 3 Model B+ Case & Stands](https://www.thingiverse.com/thing:3719217) so that I could mount it to my MP Maker Select Plus (aka Wanhao Duplicator i3 Plus). This uses 2 existing...

... surprisingly empty, so I decided to create this little logo. ...You can use the same screws as before. Here are my print settings: Print Settings Printer: Monoprice Maker Select V2.1 Rafts: No Supports: No Infill: 20% Notes: Please lay flat to print.

If you want to mount a Raspberry Pi 3 B+ with its case on the pillar of an I 3 plus or MP Maker Select plus or any clone, this mounting base is for you. ... I bought my Raspberry Pi 3 B+ from Amazon at...

Mounting the Raspberry Pi 3 Camera V2.1 on a 60mm side pillar of your MP Maker Select, I3 Plus, or any clone requires attention to detail and some basic tools. ...You'll need a camera holder, which can be sourced from Thingiverse at...

A fully 3D-printable spool mount is designed specifically for the Duplicator i3 Plus / Monoprice Maker Select Plus. It utilizes Emmett's high-quality printable gear bearings to create a rolling platform for the spool, ensuring smooth filament...

This add-on enables Maker Select 3D users to position the filament spool slightly ahead of the top gantry. This positioning prevents filament from scraping against the gantry when printing extremely tall objects or when the spool is running low. It...

This kit adds rigidity to your Wanhao i3 Plus, Monoprice Select Plus, and other similar printers. It was created after receiving my Wanhao I3 Plus, following the design of two previous braces for the Duplicator I3 V series. This mod came as a...

I designed some clip on feet for the Monoprice Maker Select Plus/Wanhao I3 Plus. These feet are to be used with 19mm/0.75" diameter or smaller hemispherical rubber feet like these...

After getting my Prusa MK3S+ I wanted to improve the quality of my older MonoPrice Maker Select Plus machines.  I've always struggled with an uneven bed and some exterior wall artifacts. ... I also found some wobble in the...

Printer Settings Brand: Wanhao Model: Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 20% Notes: In Cura, I chose Supports everywhere but set the angle to 50%. A very small amount of material is printed inside the duct...

This bracket installs an MKS Gen L and a Raspberry Pi (3 B) inside a Wanhao i3 Plus printer. Installing this is not straightforward; it requires comfort with soldering and rewiring the printer. Despite online claims, the MKS Gen L does fit within...

The mount can be used with or without the BLtouch sensor, as long as you have the cooling fan installed in the back of the printer. I purchased the lights from O'Reilly Auto Parts. There are many types of LED lamps to choose from on this link. The...

I no longer have access to that printer so further work on this file is impossible. The original designer deserves big thanks for creating such an amazing design, which I truly admire. Unfortunately, I couldn't find it compatible with the Plus...

Once both brackets are attached and the balls containing the nuts can be turned freely, loosen the screws at the bottom of the gantry (the ones you had to put in when you first got the printer) and use the balls to square up the printer, tightening...

......After a thorough search, I was unable to find an available LED strip holder that would fit perfectly on the i3 Plus, so I designed one myself. This custom-made holder should accommodate any standard width (~11mm) LED strip without needing adhesive.

This is an exact replica of the highly sought-after beginner-friendly MP Select Mini 3D printer model.

This is a model of the popular entry level MP Select Mini 3D printer Print Settings Printer Brand: LulzBot Printer: TAZ 5 Supports: Yes Notes: Rotate model 90 degrees on the Y axis to minimize supports Category: 3D Printers

Designed to elevate plus models onto the surface of the table where they reside.

The primary objective of this design is to enable the secure fastening of a raspberry pi camera to the MP Maker Select Plus or Wanhao i3 Plus 3D printers. ...This innovative solution draws from two existing designs, spool3d_canada's "z Brace for Wanhao...

My makercoin with an inbuilt 3D printer test. Single color maker coin, but you can swap filament to get dual color as I showed in the video. It has five overhang tests from 40 to 60 degrees, one bridging test, one cooling test, and three tolerance...

The Maker Select I3 Plus 200mm x 200mm x 6mm Glass Holder by Monoprice is a high-quality accessory for your 3D printer. ...This sturdy glass holder provides a solid foundation for your build plate, ensuring that your prints are level and secure...

I combined Jon Lawrence's Printrbot Simple parts to create a more comprehensive Printrbot Plus system, essentially creating a giant remix. I opted to add all files to a single zip folder rather than uploading each STL file separately to prevent an...

So if you have 2.6, replace the version number with a 6, or 3.0 replace the 2.x with 3.0 and so on and so forth.) Put the .json profile file in definition Cura 2.x folder: C:\Program Files\Cura 2.x\resources\definitions\ or C:\Program Files\Ultimaker...

So if you have 2.6, replace the version number with a 6, or 3.0 replace the 2.x with 3.0 and so on and so forth.) Put the .json profile file in definition cura 2.x folder : C:\Program Files\Cura 2.x\resources\definitions\ or C:\Program...

Ready to stop listening to your Wanhao Duplicator i3 / Monoprice Maker Select Plus printer drone on all day? Me too! This little bracket allows you to fit a BigTreeTech SKR Mini E3 mainboard with TMC 2209 silent stepper drivers. If you have any...

Ready to stop listening to your Wanhao Duplicator i3 / Monoprice Maker Select Plus printer drone on all day? Me too! This little bracket allows you to fit a BigTreeTech SKR Mini E3 mainboard with TMC 2209 silent stepper drivers. If you have any...

The Anycubic Kossel Plus Cooling System Version 2 is a highly effective modification designed to enhance the printing performance of the Anycubic Kossel Plus 3D printer. This upgrade is specifically tailored for users who want to take their prints to...

------------------------ Anet A8 plus 3D printer, in FreeCad format. Design created to facilitate the creation of new parts or modifications. It is done with the greatest precision possible. I am new to FreeCad so it is possible that the design...