maker select plus 3d printer cura

I have a Monoprice Maker Select Plus, which is actually a rebranded Wanhao I3 Plus model. This mount builds on an idea I borrowed from https://www.thingiverse.com/thing:3538544 and adapted to fit my 3mm-thick bed, which uses a spring stabilizer cup...

Filament guide to hold 4mm OD PTFE tubing. Fits the top frame of the Maker Select Plus (and probably other i3 plus clones).

I designed a custom cooling blower duct specifically for my Maker Select Plus 3D printer. It cleverly utilizes the existing two bolts that secure the rear electronics cover, replacing the original cover with an upgraded blower type fan. This...

I needed a Pi case that would snugly fit on my Monoprice Maker Select Plus 3D printer, so when I came across a design that attached to my machine without any hassle, I jumped at the chance to give it a try. ...The design was cleverly crafted as a single...

The frame dimensions of my Maker Select Plus were slightly smaller than those of the "TUSH - The Ultimate Spool Holder - with clips for Wanho Duplicator i3 Plus" designed by Silverquark, so I created a new one based on the snap-together TUSH spool...

A Versatile Mount for Logitech C270 Webcam on Monoprice Maker Select Plus. ...Demands Two 10mm M3 Screws, as the Stock Option Falls Short in Length.

Printer Settings: Printer: Monoprice Maker Select Plus Rafts: Yes Supports: No Infill: 20% Notes: Sorry, this is my first project on the printer and I used the automatic settings in Cura IIIP software provided with the printer for PLA. I did level...

Filament guides for 4mm OD PTFE tubing are a must-have tool for any serious maker. ...The filament guide is designed to fit seamlessly into the top frame of the popular Maker Select Plus, as well as its clones, such as the i3 plus.

LCD case for Wanhao Duplicator i3 Plus/Maker Select Plus with slight angle. Dimensions are close, but may require sanding to fit perfectly. Four small holes must be drilled into the case for screw mounting onto the plastic backplate. Originally...

This device serves as a leveling aid specifically designed for the Monoprice Maker Select Plus. ...The versatility of this tool, however, makes it suitable for use with other printing machines as well.

This is an anti-wobble mount that I designed to replace the original z-axis rod mount for the Maker Select Plus. I built this to eliminate any lateral wobble of the threaded z-rod, which was not supported. I used 8mm x 19mm x 6mm bearings for the...

... and 8 clips. A 10mm wide LED strip is used; it can be found on Amazon at B071KDT15B. The Z Brace Kit can be purchased from RepRap Champion at products/z-brace-frame-support-kit-for-wanhao-duplicator-i3-and-monoprice-maker-select-v1-v2-and-v2-1.

These custom-designed clips were created to securely hold an LED strip in place along the frame of my Monoprice Maker Select Plus 3D printer. The LED strip seamlessly integrates with a USB port on my Octoprint server, automatically turning on and off...

Entry point is 4mm wide, accommodating short PTFE tubing from Monoprice Maker Select Plus printer. This optimized path allows filament to glide smoothly and maintain straightness without curling or kinking. After several prints, tubing easily slid...

I created two custom led mounts in tinkercad to attach the same USB LED to my Maker Select Plus. ... LED: https://www.ebay.com/itm/USB-30CM-6W-LED-Rigid-Strip-Hard-Bar-Light-Tube-Lamp-DC5V-Touch-Switch-/322639018073?var=&hash=item4b1ec8b859

This is the Z height extension for Maker Select Plus (Wanhao Duplicator I3 Plus). These brackets add another 168mm to original 180mm, so the maximum Z height can now reach up to 348mm. In addition to these brackets, you will need the following...

After designing and building the Z-brace mod for the Monoprice Maker Select Plus, as described on https://www.thingiverse.com/thing:2349318, it became clear that side feet adapters were necessary for the column braces, since the original design only...

Add a Raspberry Pi 2 or 3 plus power supply and SD card to create an entire Astroprint setup with a bed-mounted camera for your Monoprice Maker Select Plus printer. This is a remix of several other things as noted in the sidebar, modified by adding...

The frame dimensions on my Maker Select Plus were a bit smaller than the "TUSH - The Ultimate Spool Holder - with clips for Wanho Duplicator i3 Plus" by Silverquark, so I made a new one based on the snap together TUSH spool holder. This may fit other...

Wanted an easy-to-print fan for the Maker Select Plus with new metal electronics behind the print head that's easy to install. I need high-visibility and high-clearance features. The fan offers over 270 degrees of viewing angle of the extruder tip,...

I made a dial indicator mount for my Monoprice Maker Select Plus version 2, which I think is correct. The dial indicator was sliding around on the rails, so this mount uses two #6-32 screws (3.5mm OD) to attach to the extruder stepper motor. I used...

Easy to read. ...These inserts fit snugly over standard leveling knobs found on many machines, including the Make Select Plus. ...By adding approximately 2mm in diameter all around, they make it effortless to turn and adjust the knobs with precision.

This is a modified design of the Tool Holder for Wanhao D3 / Monoprice Maker Select v2.1 by xenz (https://www.thingiverse.com/thing:2131776). I needed something that attached to the front of my printer since I'm using the SWD3 Kit Z-Axis Rear Mount.

I created this for my select plus because its home has a low slanted ceiling and otherwise wouldn't fit with a standard size spool. The extruder clears easily when using the maximum print area. You may want to add a binder clip in the rear to keep...

https://youtu.be/WmGBaHgJat4 Print Settings: Printer Brand: Wanhao Printer Model: Wanhao Duplicator i3 Plus Rafts: No Supports: No Resolution: 0.2mm Infill: 15% Notes: If you print this with a raft, it will warp - at least it did on my printer. I...

THIS LITTLE GUARD CLIPS ONTO YOUR DESK AND SLIDES UNDERNEATH YOUR 3D PRINTER, KEEPING THOSE ACCIDENTAL PAUSES FROM HAPPENING. ... **dimensions** Height: 2.86 INCHES (72.69 MM) Foot Height: .11 INCH (2.9 MM) Width: 4.43 INCHES (112.52 MM) Screen...

I modified the cooling fan mount on my printer to eliminate drag against the print bed by creating an adapter that raises it 3mm, which requires M50 screws. I now print at 100% infill, allowing me to produce larger prints with the necessary...

...I successfully achieved 240mm of usable Y axis travel after taking a Dremel to the rear of the printer belt channel hole and this modification. I might go back and lengthen the channel a bit more in the rear to gain hopefully 10mm or more clearance.

... drawer liner for cushion. The printer gets lifted 2mm by the feet plus whatever thickness your tape/foam is. I'm liking it so far: seems quieter. :-) STL, STEP and SLDPRT included. If you would be so kind, please post your Makes. ... Thank You!

The printer is now lifted by an impressive 2mm thanks to the feet, plus whatever thickness your chosen tape or foam provides. I'm thoroughly enjoying the results so far: it's noticeably quieter. STL, STEP, and SLDPRT files are included for your...