makerbot slicer 3d models

This isn't a complete remix of the playset, but rather an addition of missing pieces.\nThe set includes STLs to extend floor support structures into full circles, floor pieces and strings of rivets for the outside of the ship to cover unsightly...

To stop the filament from unspooling and winding around the spool holder between my Replicator and the spool, I made this clip to hold the filament away from the back of the case. It seems to work really well for me and appears to be doing a good job...

<p>You don't need any washers, it's spaced properly to use the bearing for everything. You'll have to print the left side and right side separate if you have a smaller machine. Uses standard 608 skate bearings. Clean up the frame hole with a 5/16...

This is a personalized adaptation of the object available at http://www.thingiverse.com/thing:44906, designed using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=44906). ...The specifications for this version include a...

This base is for placing the spool holder on top of the machine and replaces the original base in: http://www.thingiverse.com/thing:508896/

The code you provided is a list of custom parameters for an Arduino-based phone case printer, likely generated by a 3D modeling software such as Cura or Slic3r. However, I don't see any obvious issues with the code itself that would prevent it from...

This is my new extruder for the MK8 gear. The gear has an outer diameter of 9mm compared to the 12mm in the MK7, which is used in the Replicator, FF, and CTC. It requires a new aluminum cooling block (bar) that holds hotends and motors. The distance...

<p>Wanted a more skookum end stop mount for my Y axis. This mounts the the endstop at a 45 degree angle on the Y axis to take up little space and still hit the XY carriage joiners when they come around.</p><p>It's marked a work in progress, however...

This single extruder version was printed on a Replicator v1 with 'Medium' MakerWare settings (0.27mm layer height), using support and 100% infill, with three shells. Though support did not work effectively, it could be fitted in place after some...

Experience the power of simplicity with just two holes! ...Impress your friends by changing the filament once it begins to taper.

Print the object and secure it to the X carriage using screws. Rotate the motors so that the wires exit through the side instead of the top as shipped. To do this, remove the fan screws, release the pressure on the spring, take out the tension pivot,...

The printer bed delivered with the CTC Dual comes wrapped in blue tape. After experiencing the comfort of glass trays or high-end models like Ultrabase / Creality, it's a bit underwhelming. So I chose to install a Creality tray 235x235 on the...

A personalized rendition of http://www.thingiverse.com/thing:40704 was developed using Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=40704). ...The custom features include a font style of 'write/orbitron.dxf', zero font spacing, a...

I modified the original Anet 1v5 motherboard to a RAMPS 1.4 and required some adjustments, so I created a simple remix to attach a Makerbot switch on an Anet A8. This also allows for mounting a standard switch like the original design. I have an...

... better prints with a more consistent print environment, reduced warping and delamination. The complete kit is available at http://drazzticaction.com/products-page-2/3dprinters/enclosure-for-makerbot-replicator-2-2x-3d-printers-and-similar-clones/.

Remix from https://www.thingiverse.com/thing:1776429 by Meermeneer I changed the stock Anet 1v5 motherboard to a a RAMPS 1.4, i was need some modifications, so, a simply remix to mount a Makerbot switch on Anet A8, also permit, like the original...

First things first, though - I need to figure out where to install belt holders and how to align the belt so it doesn't rub against anything.\nI took some inspiration from this Thing: http://www.thingiverse.com/thing:364650 and modified it to work...

This is a Z Stop Spacer for the Makerbot Replicator 2X to account for the additional build plate thickness by adding a glass build plate, magnetic sheet, and a textured pei build plate. ...~3.3mm thickness.This one is lower profile on the sides to avoid...

4 Sand and Cut the Coffee Stirrers Then Insert Them into the Holes, Put the Front One in First About This Active Cooler Was Designed for Use with the CTC Clone of the Original Makerbot Replicator 1 / Flashforge Creator. This Active Cooler Started...

This printable part upgrades the CTC clone Makerbot replicator 1 printer with the ability to be remotely powered on or off via an isolated relay. The relay can be controlled by a Raspberry PI or similar micro controller, but can also be triggered...

The model contains the most popular formats:

<p><strong>For the Kirby Fume Extractor</strong></p><p>https://www.thingiverse.com/thing:4865478</p><p>a quick-print fan guard. Top and bottom layer to 0 layers, then adjust the infill as desired.</p><p>have fun</p><p><strong>Für den Kirby Fume...

Attachment for anglegrinder (makita cordless)for dust free sanding with diamond sanding wheels. Tape can be used as seal around edges. Keeps anglegrinder at right angle and position vith vacum. ...Does not let you to make too deep cuts at once.

Simplify3D users no longer face slicing issues with this file. The problem has been resolved by combining it with an improved tensioner and a custom simplify3D tensioner. This fusion eliminates all problems. Many thanks go to Lokster, the creator of...

This is a remix of "Articulated Tarantula (Slic3r fixed)" by Smuk3D I took all the individual pieces and organized them to fit on the print bed at the same time to print them all in one go. This is just to save you time if you print it. The only...

For the Kirby Fume Extractorhttps://www.thingiverse.com/thing:4865478a quick-print fan guard. Top and bottom layer to 0 layers, then adjust the infill as desired.have funFür den Kirby Fume Extraktor https://www.thingiverse.com/thing:4865478ein...

This game is PBR textured and optimized for UE4, featuring real-world scale measurements. It utilizes Mikk Tangent Space and includes various maps such as 2048 x 2048 Albedo (Diffuse), Normal, and RMA (Red - Roughness, Green - Metallic, Blue -...

Human- Created High-Quality LP Low Poly PBR 3D Model Ready for Games, Includes Mesh and Texturesmesh: Optimized FBX Model with 636 Precise Triangles \ntextures: Crystal-Clear PNG Files at 4096x4096 Resolution, Complete with Detailed Diffuse, Normal,...

Clockwork Orange Korova Moloko Plus Card Yeyo Cutter.