manual press machine 3d models

WYS is yours Hi, my name is Jean, living in Paris I designed a cool accessory named WYS which will allow you to precisely weigh your remaining filament on your working spool avoiding unforeseen machine stops or even worse, failed print due to the end...

So far I've had good results with my extrusion set to 100%.If you're getting weirdly evenly spaced bumps on the outside, especially if you're on a more basic machine like an Ender 3: a few things can cause this, but most likely, the printer is...

Something that didn't need supports, had no overhangs, and was pretty certain to be successful as a first print. My experience with family members that are not into tech stuff is that they have a hard time understanding how machines like 3d...

They will likely plug right into your current wiring harness but some modification may be necessary.HardwareTo mount the bracket to your bike you will need the following:M6x30 BoltM6 Nylon Nut (or M6 nut with thread lock)3/8in Nylon SpacerSelf...

Such camps are routinely fortified with lookout platforms, mechanised turrets, and barricades of all kinds.  The Brotherhood of Steel is a well-oiled military machine and their camps are no exception. Heavy-duty tents might be a poor substitute for...

Picked this “Hot-End” because it had all dimensions of the extruder and the possibilities for making the new setup a “Bowden” style filament feed with the direct drive extruder stepper motor mounted on the outside of the machine frame. Relocated the...

However, I needed to scale up the original design by 470%, which was too big to print on my machine. The original print consisted of four separate "finger" prints, and a sleeve/plug to hold them together. For this re-mix I broke each claw into four...

... improvement I will do my best to improve and then include for free for those who have purchased the snowmobile. I give no guarantee that it will print perfect on your machine or that things will not brake when you send the sled flying off a cliff.

These tend to be about 40-50g each, and I measured a typical diameter of about 140mm on the loose filament- I think it generally uncoils to about the width of the baggie it's shipped in. The innermost opening, where the spool is meant to go over the...

SLOT 290mm Hardware parts: 16 pc - M3x10mm socket button head screw 4 pcs - M4x25mm SH (socket head) screw 4 pcs - M4x20mm FH (Flat head) screw 4 pcs - M4x10mm SH (socket head) screw 4 pcs - M5x35mm FH (Flat Head) screw 14 pcs - M5x35mm SH (socket...

And a timer at the end of the print to buzz a sound once the parts has cooled down. Do not use the g-code file on other machines than MK3S+ ! ...In any case, I recommend you to slice the .stp files by yourself to make your own g-code...

Need to simulate the speed pot. Rough schematic is here https://td0g.ca/wp/wp-content/uploads/2019/11/2019-11-30-500W-Spindle-Controller.pdf (Thanks for that Tyler) Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 Plus Rafts: No...

En mi caso se han usado los de la placa.La cadeneta usada que se ha usado es la siguiente (opcion 20x10mm open, comprar dos...

I usually fit my printers into an enclosure of some kind which usually have some form of illumination but the Predator is such a large machine and can be adapted with its own enclosure, I figured I'd install its own independent lighting system. ...

There's even a couple companies shipping machines with it already applied too. If you don't have a heated bed, the "lamination procedure" would still apply, but you'd probably want to use a different laminate/material/substrate... I've had decent...

It came out decent, but I know the machine can do better once the pilot is less dumb. Might also just go with PLA since that would be just fine but all I had was grey, so I used PETG for black.</li><li>The LCD selector wheel just BARELY rubs the...

The variables to change in the Y-AxisBackPlate_Rev.scad file for your specific machine are: i3v = 10; i3v_Width = 297; //10" i3v i3v_Vslot_Width = 189.58; //10" i3v i3v_Vslot_Offset = 62.9; //10" i3v i3v_MotorOffset = 141.0; //10" i3v In case you...

to remove push from the angled face (from the thickest portion) outward and it will release itself from the extrusion.The ideal position is up against the top of the frame, tighten the extruder and make sure your PTFE tube is pushed in all the way,...

(Each coin takes about 10 minutes to print on my machine with these settings.) The model is very forgiving so just about any print settings that can produce something will work. Details: This is a very easy print. I tested with a 0.4mm nozzle, but...

That, plus my eyes are starting to fail me and I find I need more light these days,\nOriginally, I was going to make some LED blocks with 3W LEDs, but when I was testing the LEDs, they got rather hot so some machining needed to be done. I got lazy so...

Iterative design can also be a learning objective depending on your access to a machine over a several-day (or week) period. Objectives: Although your collection of playdough tools will increase and diversify as a result of this lesson, the real...

Additionally, it utilizes the full potential of my printer (25cm wide), making it unsuitable for smaller machines. - The barrel at the front stabilizes the cars but is limited in size, preventing some models from fitting inside. However, a vast...

Saying that, it seems like the company is listening to feedback as there have been several design changes made to the original machine spec. My first issue was with the gantry carriages. The way flimsy acrylic is used to pre-tension V-wheels is...

BUT: Since the Probe center is now positioned minus 5mm more to the front of the machine than the center of the nozzle, it will not be able to calculate the correct UBL/ABL Bed Level data since you're always 5mm off. To compensate for this (in...

Aluminum tape to be used for insulation will have a vital function at preventing any noise being created while operating your new built machine of great beauty with it when installed well - however do assemble with electronics at own risk! Remember...

As I said, I used the fan of mrah (https://www.thingiverse.com/thing:2333438) but I modified it because on my machine, If I let the fan in the continuation of the motor, it hurts at left when a "home" command is done. So I inversed it, puting it...

the original thread contains 2 rings below the thread that are not necessary for modelling your own models.The first is the tamper evident bead or locking ring, which probably nobody wants to use here.The second is the support ledge, which is only...

A set of tracks and interactive parts to create your own marble run/marble machine! The tracks can be printed as needed and rearranged into different layouts. The tracks are designed for small print volumes in mind (also because my printer is small)....

There was Meme created named "Oblivion NPC Conversation Meme" (Bethesda Game Elder Scrolls Oblivion) which puts a hyperbole on humans that act like slow machines or non-playable game charaters. The YouTube channel "Whacked Out Entertainment" used...

These uni servo adaptors will fit in the center of the gears 3D prints as well.6) M3 (assorted lengths), M3 X 12mm & M3 X 8mm machine screws and Nyloc nuts.7) Base standoffs are four M3 X 36mm.7) 1/2"-20 stainless insert, insert using a soldering...