mechanical engineering design project ideas 3d models

If you like the black vase in the pictures, I made it using PaulM's Customizable Spirograph Vase Generator - http://www.thingiverse.com/thing:53916 Instructions: These flowers are a blast to design and print! Each print job is fun since there's a...

For stepper driver increase the current via the potentiometer from low to high until there is enough torque. I highly recommend the 608 bearing upgrade from Leviathan3D: https://www.thingiverse.com/thing:4100518 Print Settings Rafts: No Supports: ...

A Star Wars themed poker set to add a sci-fi vibe from a galaxy far, far away to your next game.Designs are provided for everything shown in the pictures and include the following:Head & tail sides for $0.25, $0.50, & $1.00 denomination...

So for Motic 143 and Lifecam HD3000 I did all the job for you and designed the exact correct bracket. For other combination - use it as an inspiration, get digital caliper and start measuring! A microscope will have an IR cutoff filter (cyan...

... The ripper is a sword type design and it will NOT fit in any other Beyblade launcher. I made mine in PLA and it has never broken, in fact this exact launcher has been used over and over again (pulled at speed). DISCLAIMER: It's not indestructible!

* ALT Components Lid Base * ALT Components Lid Top (this is another lid that you should switch filament on roughly halfway) * ALT Dice Tray * ALT Group Token Holder * ALT Special Tray * ALT State Tray * ALT Token Tray THANKS Special thanks to James...

Gingerly push the pen holder onto the heat sink – it's designed as a snug fit, so you may have to scrape it a bit to make it fit on just right. Hold it in place with the fan mounting spring clips. Mount the pen in place at the right height, send your...

Now, the older machine profiles for the pulley and plus versions that worked well in Cura 2.x-3.4 are still available in the designated zipped file. Additionly, the newer pulley and plus machine profiles for the 3.5 and above versions of Cura are in...

This is a design choice made by https://www.diabetes-katzen.net in their excellent [paper version](https://www.diabetes-katzen.net/images/insulinspritzenmass/Insulinspritzenmass_mit_Erkl%c3%a4rung.pdf). Because we were initially using that, we kept...

As a designated and protected historical site of Japan, this makes for one of the more stunning 3D building models, complete with gate (Karamon), courtyard and the famous great hall (Daibutsuden) housing a giant bronze Buddha statue. The building and...

The file is designed so that it can easily be printed over the washer.You need the following screws and melting threads for a wheel:M4 melt thread:10x for wheel guidance28x for the spacers 1 (2 each per holder)M3 melt thread:2x for the outside of the...

...I wanted to center the spool on the axle, so I made a spool spacer, designed for the 1kg spools Printrbot sells. [They may have since changed manufacturers. Measure before printing.] If your spool inner diameter is around 51mm, this spacer will fit.

This is my first go at designing a full size printed Crankbait. I think the finished model and results (fish caught) where well worth the effort.</p> <p>The bait is printed in two halves and then glued together. (I used super glue) Three small pieces...

It has an stellar companion designed HDE 226868, a supergiant blue star of 20-40 solar masses. The distance between them is enough to prevent the black hole from striping away material from the star, but its stellar wind is constantly feeding the...

However, it is not always convenient because you want a more customised solution (colors and length in my case), or simply because the shipping time and cost are high (also my case).All in all, it is even more cheap and convenient to print our own...

Hardware needed: Two to three 608 bearings and the internal sleeves too if using an M5 screw, which is what I designed this around. One M5 nut, pressed and glued into the piece that glues into the front / top smaller circle. You don't have to glue...

I decided to use 608 bearings and designed some threaded clips to align the pulleys, keep them in place and to allow for fast rearrangement of the pulleys when putting in a spool with different width. In addition I was unhappy with how most spools...

This is a completely new version of my original design (here: https://www.printables.com/model/145632-dslr-rig) without the cage and with fewer parts. Redesigned in SOLIDWORKS for higher precision.UPDATE (19/04/2023):Uploaded .STEP files (exported...

I tried that but I'm not terribly patient and I never got results I was satisfied with.These models are designed to support embedding magnets in the hexes. The mold created from “Ring mold” has 12 slots (2 per side) for 1/10" diameter, 1/16" thick...

(Blinds control etc.) The power supply is specifically designed with 24V, because the supply line is long. By the LM2596 DC-DC buck converter voltage regulator a stable voltage of 5V can be set at the D1 Mini.</p> <p>Im Sockel des Drehkopfes ist ein...

This system is designed to work with the mini-pump mentioned below and can be scaled down to 90% to fit on Rep2 style printers. It's not perfect, but it works well enough to grow lettuce and herbs and maybe more. The variety of lids, baskets, and...

Now, the older machine profiles for the pulley and plus versions that worked well in Cura 2.x-3.4 are still available in the designated zipped file. Additionally, the newer pulley and plus machine profiles for the 3.5 and above versions of Cura are...

It's designed with a fully 3D-printed frame and rotor, no screws needed. It runs on either battery or DC power adapter, so you can take it anywhere! This tool is very useful for spinning down PCR mixes in tubes, as well as other applications that...

Depending on the design and construction of your hairstylist, you'll get different values. However, that doesn't matter since you can adjust the adapters accordingly. The adapters work with a 15 mm intake, which is freely configurable. How thin you...

...I have updated the design of the carriage to increase the clearance and will label it at Y1.1 and Y2.1. The minor amount it rubs shouldn't effect anything, but if you wish to change them to insure no issues, the updated files are now in the set. 3.

The design is now even more water-resistant than before. Adding a small amount of grease between the hatch and cap ensures it's nearly waterproof if the hull has been painted. The hatch utilizes standard RC Body clips to secure the cap or paper...

This is a recreation of the soda can tank I made a remix of, unfortunatly the original files from the original creator are no longer available.Therefore I made this.Contains all pieces from my Remix too.If you like my work please consider supporting...

So why not design a rectangular case that will fit both boards and use inexpensive 5 x 2mm magnets? Because only 4 connections are required between the two circuit boards, the housing has remained relatively flat at 25 mm. The 4 pieces of wire...

These are designed to work with M8 bolts with DIN 912 heads, or anything smaller that would fit inside them. (M6 should be fine, for example, although I haven't tested that.) Again, see the photos for examples. ### Two clip variants There are...

If a player has cast 1,2 or 3, then he/she needs to choose one of their pawns and move it that many squares along the path designated for that player. The player needs to be able to smartly choose a pawn to move, so that it optimizes his chance of...