mercury planet 3d model

The model is amazingly easy to fly. https://www.youtube.com/watch?v=rsS5YetUQyA The video quality is less good - this time I had to film myself. There are two hull versions. The longer version (lv) is the one shown in the picture and video. But...

https://www.youtube.com/watch?v=Nn9B46IjsVU ______________________________________________________ ENGLISH ______________________________________________________ Only tested on T12-X, but can work on equivalent models with boxes of the same...

 The fan mounting holes are sized to accommodate a Brass Heat-set insert size M3x4mm.  The holes are not threaded and too large to accommodate an M3 screw itself.   Upgrading the Raise3d Pro2 with a Copperhead  Note: Both Hotends must be replaced...

This + rotating the model upside down let's me print the whole thing with no support at all - my print time was 2h 39m and I used small, low-density raft, just in case. https://www.thingiverse.com/thing:4565091 Another thing - it appears that the...

(I used bodies instead of components to avoid model breakage in case of major size change.) Required Parts list and where I got them: 1X 2032 battery holders: https://www.amazon.ca/gp/product/B08SQRSTJ4 1X rechargeable LIR2032:...

Have fun and use common sense ;) This is my own creation and the model can also be found on Thingiverse thing:3771579 Print instructionsPrinting info: Printed on Prusa i3 MK3S, PLA 0.2mm layers, 4 perimeters for strength, main mount was printed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_pattern_thickness = .8 custom_back_extra_port_y_size = 30 custom_back_camera_corner_resolution = 8 custom_top_port_x_position = -10...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

... to be retained and passed through, if desired. Can be nice if you want to completely remove the controllers from your hands at times without needing to set them down. Happy Printing. I would love to hear in the comments if you use this model.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_shape = 3 custom_right_port_length = 30 stencil_drawing =...

It's just a model I whipped up, and sliced it with a bunch of retraction changes. Then went back and spliced all the g-codes together. Base Cura profiles I use: layer height - 0.2mm Optimize wall print order (do not retract before outer wall), print...

A perfect fit for your specifications, this model features the following options: picture =...

- Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

I started with the photos of the metal models (I've uploaded those photos to thing:1618843) and went from there. All the design work was done in Moi (Moment of Inspiration). Once I had an escapement design, I ran it as a simulation (unsuccessfully)...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl, and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

Which means planning so the bridges will look nice enough/not stand out too much.This also means some very precise modeling so that the slicer can handle a bridged over area with a hole in the middle. Here, I build up to it layer by layer with...

I will be answering questions there and I look forward to seeing pictures of people's in-progress builds: https://www.thingiverse.com/groups/curta Update 6/27/2017: The main axle and step drum model have been updated. The old one works, but the hole...

The model shown has six in each ring for a total of twelve. Print one of each of the remaining files. Carefully remove any burrs or imperfections in the print especially on surfaces that move against one another. The “Spinning Terrain” prints...

The Doors Pack includes 47 models (each in .stl and .obj format, making for 94 files) and adds a treasure well of different doors to make your dungeon unique. It is also the first expansion pack I got ready to publish. Some of the doors come in...

I could not find caps / hoders which suited my project, starting from inspiration of certain models existing in AA, I made a design under fusion 360 which corresponds in the size of integration, as well as the possibility of making spot welding. ...

 I use a cheap little fingernail drill to do most of my sanding as a dremel can somtimes be overkill and it comes with a ton of little heads it'll take me years to use up.https://www.amazon.com/dp/B07T8H3531?ref=ppx_pop_mob_ap_shareThe final...

That link also calls for using alanho's file to hold the TFT50, here is a direct link to his page as well: https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/alanho/BTT_PITFT50_v2_Mount I also made some simple changes such that it...

All overhangs should be 45 degrees or less. Rafts: Not required, unless you experience adhesion issues. License The "Hard Drive Holder" models (.stl) are licensed under the CC BY license by Code and Make. The "Hard Drive Holder" code (.scad) is...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

 I'm confident anyone here can just casually rotate the model right-side up in your slicer.This is licensed CC BY-SA 4.0.  Please feel free to republish this.  Feel free to remix this.  Feel free to use it for commercial purposes and make loads of...

I have printed the model in 2 colors with an extruder, changing the color of the filament in Z: 150, except in parts 1,2 and 3 that have part of the roof and I have changed it in Z: 150.02. The dial I have changed the color of the numbers. I bought...

Will require manual tapping. Base Base_Type - The type of base (round or rectangular) Screw_Hole_Diameter - The diameter of the screw hole Screw_Head_Diameter - The diameter of the screw head Screw_Head_Countersink_Angle - Screw countersink angle...

This project is intended for use with circular lenses that are delivered in glasses ordered from Zenni Optical with this particular frame: https://www.zennioptical.com/p/metal-alloy-full-rim-frame-with-spring-hinges/5500 For either model of Quest,...

Please note the Modular Assembly Preview STL is just to show a preview of one assembly model, not for printing. Here's a brief description of the types of parts included. Cuffs - Number is the inside diameter of the cuff. Diameters include...