minecraft stumpy cat 3d models

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

I added some build notes below and a BOM which doesn't include screws, wires, connectors, etc., but has all major components. I planned to revisit this model and release a better version. However I have at least a year's worth of projects in...

EX6 Arcade Fight Stick What started as just doing a few tweaks to an existing model turned into a near full redesign and a (almost) fully printable arcade/fight stick case platform; the EX6. Printable on the Ender 3 or any 200x200 printer. The...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 3 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

The COMPLETE Svartwood Trolls bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Trolls comes in all size and varieties, and being one of the most ancient people, no one knows...

*Download new version 1.01 here: https://www.printables.com/model/178925-ender-3-s1-stealth-light-bar-easy-to-print-and-do-mod ( Maintaining on Printables ) Easy to print light bar that uses the built in accessory port for power. This allows for...

Remember to check the wiring of your relay if you use a different model or brand. Adjustments If you set the microswitch to click when the bed is at Y=220, then it will work out of the box with Cura. I still recommend you to modify you G-code to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Slice your model in your desired software and save your gcode 3. Place the created gcode in the same folder in which you extracted the exe 4. Double click to run the exe 5. Type the number of the option you wish to use, for the towers included in...

2022-04-14 I started to create a new base that could use threaded inserts and quickly realised the base models had become quite complicated due to the iterative design process, so I went back to basics and recreated them. The new housing mechanism is...

 You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid.  This can be...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Thank you very much and happy printing!Updates13/02/2022: Redisegned T-Slot-Clip so that the PTFE tube does not interfere with the cables on the side of the Raspberry Pi (see picture below).PrintingLayer height: 0.2 mm;Material: PETG (recommended),...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

If you don't want to mess with a PLA support, you could probably print this part in two separate objects.I provide you the Fusion 360 file, so you can customize and change the model according to your rail system. I strongly recommend you to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits the...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

For the launcher and the “motor” (= nozzle and adapter) you can find additional info here: https://www.printables.com/model/46571-water-rocket-and-launcher-platform-complete-instru These parts have been proven to be working (see old video). The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...