mini models links

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Did not want to spend a big amount of time 3D modeling a cable tie). What I like to do is build the whole assembly on a short piece of 90mm pipe (as shown) so I can comfortably work on my workbench. Then, by using a 90mm joiner section, I can simply...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Print Settings: Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: .15 or .2 Infill: 50% Notes: Tolerances may vary. Please direct message me if you're having trouble in either direction (too weak or too stiff). A...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

I recently built some model catapults, and I realize they just use a peg to hold arms into place. So I borrowed that idea, using two interlocking pieces. One piece (looking kind of like a ladder) inserts into slots, and pegs from the top hold the...

http://creativecommons.org/licenses/by-nd/3.0/ # Summary [#3DBenchy](http://3dbenchy.com) is a 3D model designed by us at [CreativeTools](http://creativetools.se) specifically for testing and benchmarking 3D printers. It is a small recognisable...

 I'm confident anyone here can just casually rotate the model right-side up in your slicer.This is licensed CC BY-SA 4.0.  Please feel free to republish this.  Feel free to remix this.  Feel free to use it for commercial purposes and make loads of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

- The barrel at the front stabilizes the cars but is limited in size, preventing some models from fitting inside. However, a vast majority should fit without issue. PRINTING: - I print the main body and shaft separately from each other, as well as...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

I recommend scuffing the outside of the drawtube with 350 or finer grit to minimize reflections and improve motion. See photos for assembly. You will only need 4 3D Printed components for this focuser:1 Main Body-Hadley-focuser2 Turn Knob...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

If you start with the STL files, they will all be 100% scale and in various orientations - these orientations are from the CAD model and are typically NOT the best orientation for printing. If you start with the 3mf files you can easily change the...

I have printed all of the parts and assembled a model which is shown. The "Dome" cover will fit over the Base Plate, and in turn a 1/2" piece of sprinkler pipe will fit over the tabs in the center of the Base Plate. The Mic Holder will fit over a Gen...

**Just make sure they are all the same voltage and be very carefully** - **3S BMS 20A** - I used the HX-3S-FL20 REV2.2 Probably they are more models similar to this, this was the name I found. This is for controlling the charge and discharge of the...

Features2 emplacements for 3.5" Hard disks, connected via USB3 to the Raspberry Pi140x25mm fan emplacement at the front for efficient cooling of the Raspberry Pi and hard drivesInternal Power-supply 5V/12VMain power switch and fuse accessible at the...

Here is what I came up with: This model consists of 3 printed parts. Then you need something with ø3 mm diameter as an axle. Anything like a wire or nail would do. Just cut it to a length of 18 mm. Fix the lever in the holder with this and make...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_width = 100 use_mouse_ears = 0 pattern_element_overlap = 52 stencil_shape = 3 custom_back_camera_y_size = 20...

Constant testing and printing are underway with mods on nearly every model, wasting over 300 feet of filament in the process. I'd appreciate support for my project as it's not intended for non-3D users but rather for those who want to quickly build a...

By the way, even though adding a vertical ring might seem counterintuitive, it does provide added stability while still maintaining the original model's benefits: no need for supports, and you can print directly without worrying about brim or...

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

Existing models didn't meet my needs, so I created a parametric part. The current parameters are tuned for use with an M6 thread and prior tapping. I recommend printing a test part (produced by setting debug = true) to ensure your tolerances are...

O3DS version coming sooner or later.EDIT (11-21-2021): Finalized the 3DSXL design (slightly wider with larger radius fillets inside the slot), changed all meshes to the new CADQuery version, added an MMU SNES-themed model!EDIT (11-22-2021): Updated...

I needed a quicker and simpler solution to perform these tasks so I could focus on slicing and printing actual models. What is more basic than some good old push-buttons?</p><p>Feel free to remix it as you wish. It would be nice if you upload the...

I have completed assembly and everything works so this addresses some of my main wants for this awesome model. I am also going to include the full parts kit here (the originals I used also), so everything you need is in this one thing saving any...