moai 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

Trim/Cut plastic flowers from a dollar store. Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to...

What fun! To build an adapter to your requirements, install Blender v3.80 (or later) and open the T2M42atapter_pre_assembly.blend file. Select menu View | Front (or press number [1] key on the keypad) to view the model from the front against the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Fits both "Research" and "Research Plus" models.Don't loose precious time with clips or carousels!Print your holder now ;-)Materials required4mm aluminum rod (2x 18cm minimum)2x M5 20mm screw with hex head2x M5 butterfly nut2x M5 washerSuperglue or...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

MAJOR UPDATE [2017-05-05]: New and updated models were added based on suggestions and requests from people who have printed the terrain set (thanks abchiptop). Work log checked off... Checked all decks to be same dimension (5mm thick) - [x] Checked...

Originally designed for the Ender 3-V2 model, reusing the 4011mm Original axial Fan as Nozzle cooling. The original fan is loud, you will probably wish to change it with a quieter one and higher performance 4020 axial fan! Many options are available....

Finally, if your printer's bed is larger than mine and can accommodate the full required width of the inserts, you can merge the included additional bodies Body30, Body67, Body68, and Body69 with the corresponding model parts. The weight of each...

I can only describe what I did or share my experiences and provide respective models and a SketchUp project concept file (the .skp file) so that you can adapt or improve it for your Stargate. In one of the comments from '5ft Lighted Stargate'...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

This model fits seat shafts with a 16-groove, skip-tooth-top, 12mm nominal shaft: (note skipped groove, blue arrow) Probably best to print these with the spud pointed up for minimizing how much trouble the overhangs inside the hole will...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

You can use a polarity detector app on your smartphone to figure out which side is North (+) and which is South (-).If you want to risk glue breaking loose and would rather not print the magnets into the piece, then you can just grab the models and...

... diameter of the hose end 30mm away from the tip (the wider part) This will give me the diameter and taper needed to revolve a new part for anyone who wants one. Please let me know what make/model it goes to and I'll add it if I am able. ...

The COMPLETE Requiem Brotherhood bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Requiem Templars (presupported) Requiem Templars stand before the chaos...

... that is about 1/4"/5mm in the front center due to the belt tensioning clip bumping into the blower. Unless you like that kind of centrifugal blower fan on belt tensioning clip action, I recommend not to drag the models dead center to the front.

I found when doing this I had to clean my hotend and its was really difficult with this model. ... I included my wires for my NEMA17, but I can tell you right now, your NEMA17 will not be the same, you will have to figure out your pinout by yourself,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

The source of the model has several parameters that you may wish to change. The current settings are for a silicone tube with an internal diameter of about 4 mm. You can adjust the pen length and width to your preference. Note that some tweaking may...

FLSUN doesn't seem to be OK with the idea of sharing the CAD models (their loss...), so I didn't include the machine parts I reverse engineered (the effector is present though). The extruder is very crudely made, so I left it. How to build : ...

... Print Settings: Printer: Fused Deposition Modeling (FDM) Layer Height: 0.1mm Infill Density: 30% Support Material: Hatchbox PLA Post-Printing Instructions: Mirror Testing: Position the tester near the radius of curvature of the mirror to be tested.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 16 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

It may also have fitment issues with non-TM branded or aftermarket upgraded models. Please read the Print Settings section for details. ==CONCEPT== The JTW HCC-2A is the evolution of the Hi-CAPA Carbine Version 1...

* I rooted my tablet (google for instructions for your particular model) * I installed two free Android apps: "txtpad" and "init.d scripts support". * I used "txtpad" to create a script (a text file) in the default location, containing one line...

Currently, there are three models:Ebook Reader Holder (1x3):This was designed for my Kindle Oasis in its third-party case (if you want it for something thicker than ~15mm, let me know and I'll see about whipping you up a variation)1x3 footprint on...

Related models: Track connectors for wooden railway to Plarail (and other systems) https://www.thingiverse.com/thing:5024058 Various other items of rolling stock: https://www.thingiverse.com/densha/designs Note that many 0-gauge (O-gauge, 32mm...

I printed the nuts and locks in a bright colour to highlight their function and make them easy to find if they were to fall off. I have uploaded a 3mf file containing all the parts in the correct orientation on the build plate, however you...

It is not necessary to add this "torus".)Seam positions:   Aligned:  Pegs, Discs, Base, Storage Box Lids   Random:   Cover, storage box basesFilament color changes:If you want to use different colored filaments as I did,...