models with cellulite

Using the following options, you can create a customized version of http://www.thingiverse.com/thing:310541 with Customizer! ... Thickness: 0.5 Pixel elongation: 1 Pixel shape: 0 (Default) Grid size: 0.3 Border width: 0.75 Orientation: 1 (Default)...

This trick present has a hidden latch mechanism that will keep it securely closed until you twist the topper on the lid. PrintingFor a square boxes you will need1 square_lid1 square_base_[small/medium/large]1 square_spring2 square_latch4...

Install the 6 spacers on the vertical arms of the printer with 2 on each arm evenly spaced. Install and center the 3 fixed panels. Use business cards to create space between door panels and tape them together, then center and tape them to the...

The only aluminium pipe I could find at local store was a metric system aluminium pipe (10mm diameter, 1mm thick). I also wanted the top wheel to be turnable but firmly fixed to the pipe so I splitted it into 3 parts fixed with a M3x20 screw. So I...

I may tinker with a Halbach array (directed magnetic field) at a later time to mitigate or reduce this initial repulsion... but I suspect there isn't enough room between the belts and bearings to do that properly. I have printed and wired this for...

I have a DaVinci Pro 1.0 and I use the E3D V6 hot ends with his mount. The only draw back to this design as far as I can tell, is the use of sheet metal or wood screws in plastic. I discovered these tiny brass nut inserts on Ebay. They have 3mm...

If you want to add a third degree of movement to the legs, you can replace the "servoless leg" with a "midleg" servo holder and it will work just fine. We used two degrees of motion to keep costs down and weight low. When I added the third servo to...

The recesses are sized for the rectangular guards on the handle so this might work for other files but it definitely works nicely for these. I listed the pegboard 2 position blank as a source but I had trouble using the geometry cleanly in SketchUp...

However, I can't help with troubleshooting your own project or Inkscape. Be sure to read over the Eggbot Wiki at Evil Mad Scientist. Note: A Google Sketchup file is included for reference. ... **Original Size Images** Front View:...

Though, there's no reason why you couldn't hang it from anything with a smaller diameter.Maximum width of the spool can be up to 80mm (this leaves 5mm of margin). The maximum outer diameter of the spool can be 210mm (before you can no longer hang it...

I also updated the regular PSU Holder with additional support and lifted it up 10mm, allowing for a 220mm graphics card. ----- **Update 2:** I added an alternate version of the Right Riser Card Support, which allows for a 300mm graphics card...

Racing Wheel Design presents an I-FLAG and gear indicator engage with or without cap plus removable brackets in all directions to attach it to any simracing setup. Race list: 1: arduino nano ...

Enjoy design! It's small switchbox to turn on and off the fans and lights.The box is inserted in rectangular hole in Ikea Lack table top                              ...

I printed mine at a speed of 50, with a resolution of 0.2 mm. Assembly instructions below, assembly photo above. As always, any questions, don't hesitate to ask.Assembly:See numbered photo for reference.During assembly you'll want to keep an eye on...

There were plans for her to command an all-female crew to Salyut 7 on International Women's Day, but this was cancelled due to problems with the station. Kondakova eventually retired from the cosmonaut corps in 1995 and now, in her sixties, serves as...

The links to the used parts can be found at the bottom of this description.\r\n\r\nI printed the motor mounts using Fillamentum Vertigo gray filament, which has a great metallic look and works well with 38mm aluminum spinners.\r\n\r\nTo my surprise,...

### In order to get it to work with option 2: - Hook the sensor up to the free Y-endstop port (Important: switch the plus and signal cable in the plug as they come the wrong way around from the factory -> check Sbase pinout (pin furthest away from...

Tested on soft ground (sand ground and grass), ceramic floor with relief and sandstone floor, improving stability, accidental slippage and preserving the ceramic floor.Optionally, you can also print the part Anell_TPE, as an additional anti-slip ring...

Boxes printed with 'MAG Tabs' slightly lower the available volume for dice. Quick Fix: Scale up box Top Half in the Z (Vertical) Direction ONLY. May result in unwanted gawking at your unnecessarily large box. You've been warned. I do not condone the...

Customized version of http://www.thingiverse.com/thing:53235 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: snapAxisSlack = 0.5 GENERATE_CASE = 1 baseFrequC0 =...

Changelog: Version 2.0 (October 2022) The Fram FM25L16B-GTR is replaced by an Adafruit breakout board with a MB85RC256V chip, this requires a partial new Arduino code. The components are now placed on a print. The microcontroller and Fram are...

The charger is connected in parallel to the battery.The entire circuit is low current, so when coupled with three cells in parallel,  should provide a long run time.AssemblyPlease refer to the video above for a guide to assembly. The CAD and video...

If the Celts ever had to clear land in order to build new settlements, they would plant an Oak tree in the center of the clearing in order to honour the Tree of Life and ensure prosperity.If Celtic tribes were ever at war with one another, they...

Not sure if it's even necessary because everything is very tight, I had to carefully hammer the legs down with a mallet, but I recommend, just in case.Check two tests I made after this upgrade and judge by yourself! 20x20x60 Test Tower to show the...

Make sure the orientation is correct with the front of the middle part having the two holes for the knob and aux port. Once it is slid in place just us some glue to hold it in place. Next put the speaker drivers into their designated holes and use 4...

As a result of the elevated currents which have to be managed to warm the bed, especially while working with materials such as ABS, it is highly recommendable to have a device at our disposal in order to handle all that stream and release our MB of...

Use a little heat from a hot air gun or even your heated bed, cover the object with a metal or glass cup and heat it until it is just slightly plastic (but too much heat will cause the object to be deformed). You can do that if you don't have...

My own personal version has a 0.5mm carbon fiber sheet on its bottom which though I doubt adds any real degree of strength (0.5mm is almost paper thin and can be easily cut with normal scissors) it does offer a degree of protection and definitely...

A carbon fiber filament might help with durability, but I haven't tried. The easiest way to set the canister to "stage 3" is to use the other tool in this project, which is...</p><p>The other tool is the winder tool, used to unwinding/rewinding the...

Customized version of http://www.thingiverse.com/thing:56310 with options: ring_thickness = 1.6, shape = 0, objectThickness = 5, custom points =...