monoprice maker select plus auto bed leveling 3d models

... Set the boundaries for probing (where the probe can reach). #define RIGHT_PROBE_BED_POSITION 195 #define LEFT_PROBE_BED_POSITION 30 #define BACK_PROBE_BED_POSITION 135 #define FRONT_PROBE_BED_POSITION 8 for home center. ...#define Z_SAFE_HOMING 1

Control box disassembly video: https://www.youtube.com/watch?v=bXQ1gAid17Y Print Settings: * Printer: Monoprice Maker Select * Rafts: No * Supports: No * Resolution: 0.2mm * Infill: 100% * Notes: Don't forget to rotate the standoff to fit on the...

ENGLISH: A standard X-axis carriage set, suitable for mounting an automatic leveling table without issue. No problem is mounted unmodified to the carriage. It necessitates a servo drive MG90S or similar in size as well as any accessible limit switch....

A self-leveling system for P902 is achieved using a microswitch and micro servo SG90. This solution offers precision and reliability. ... Watch this video to see the system in action: https://youtu.be/bGeNh6JVzZM For the microswitch, visit:...

Tinkercad model available Print Settings Printer: Monoprice Select Mini Rafts: None Supports: None Resolution: 0.175 Infill: 50% Notes: Printed using eSUN PETG Sliced with Cura 2.4 To print this part, you will need to position the printer at an...

PROJECT SUMMARY: This modification expands the MonoPrice Select Mini's print bed depth to 230mm at an affordable price. I can utilize a printable area of 130mm x 220mm with these modifications. The cost was approximately $60 for me, nearly the same...

This is a modification to expand the MonoPrice Select Mini's print bed depth to 230mm on the cheap. I've managed to utilize a printable area of 130mm x 220mm with just these modifications. The price once built was approximately $60 for me, nearly...

I wanted to use an E3D V6 on my Select Mini v2 but couldn't find a suitable way to elevate the bed to compensate for the V6's increased height compared to the V5. These spacers are 10mm in diameter with a 3.5mm hole running through their centers and...

The original design didn't quite fit my Monoprice Select Mini. It missed the switch lever by a hair, with the end of the arm bracket barely touching it. In fact, the original didn't even come close to hitting the lever at all. To fix this, I...

... a modified and cleaned up rear rail. I am going to print these pieces today. Any helpful feedback is appreciated. Update: decided to use PLA - these components won't be near the hot end and the bed won't get hotter than 110c, so it should be okay.

I started by lowering the bed, zeroed out my machine, and slowly raised the bottom nut while re-tightening the knockoff spring. If it wasn't close enough, I loosened the knockoff spring, turned the bottom nut a bit, and re-tightened it. ...Ideally,...

I adored this extension concept initially, however, I soon realized that it wouldn't accommodate my newly acquired 300mm x 300mm bed, so I made some adjustments accordingly. To make the necessary modifications, I primarily needed to create channels...

It requires recessed bed screws and updated firmware, including a new board, to extend the bed all the way to the corners. It can be used with stock firmware and bed as well, but you'll need to add a spacer glued or taped where the X endstop hits. I...

This sleek new shroud perfectly complements a standard 40mm x 40mm x 10mm fan. Securely attached to the heat sink using super glue, it provides an efficient cooling solution. The additional fan is wired in parallel with the existing cooler,...

I was searching for a bracket positioned at the back so that the threaded rod doesn't stick out in front. I couldn't find one, so I decided to learn how to create things using Fusion 360 and came up with this design. I'm not sure if it works well or...

This will probably work with either the cocoon create or the wanhao I3Plus. This will give you a complete, unhindered view of the nozzle as it is printing from the front of your printer. To install this, you will need to relocate the PCB. Here is...

I designed a blank version to achieve a cleaner look. ...Enjoy.

This should also work with Cocoon Create or Wanhaou I3Plus as well. I wanted to install a fan duct that attaches through the rear side of the printer. The PCB was connected to one of the lower bearing blocks, so it had to be relocated. Ideally, it...

This is a sleeve case combined with a mounting plate to fit on the right side of the printer.

I needed brighter lighting for my printer, and my desk lamp was creating annoying shadows by pointing directly at it. I discovered some LED strips that could be wrapped around the edge of the printer frame, but the problem arose because the frame...

I encountered difficulties securing the back of my camera case, so I retrieved the original files for the Prusa i3 and imported them into this system. The following files comprise all the prints I've made that have proven successful for me. ...Special...

This is a versatile attachment that combines a protective sleeve and a sturdy mounting plate, designed specifically to be mounted securely on the right-hand side of your printer.

## Ender 5 Plus bed leveling test.

Like many Monoprice Mini Delta (MPMD) owners, my printer does not print evenly across the bed (even with the G29 auto-leveling set). As recommended on the "Malyan M300 Mini Delta 3D Printer" website (https://mpminidelta.com/) I am following the...

Adjusted the design to match the precision hole pattern of the Monoprice Maker Select V2's bed plate.

This is the LCD cover for my Monoprice Maker Select Plus, utilizing the Wanhao Duplicator i3 Plus LCD enclosure and the Modular Mounting System.

Filament guide to hold 4mm OD PTFE tubing. Fits the top frame of the Maker Select Plus (and probably other i3 plus clones).

I optimized this for the Maker Select Plus. ...This printer lacked a few key features, so I downsized it to utilize the standard tools that came with it.

Filament guides for 4mm OD PTFE tubing are a must-have tool for any serious maker. ...The filament guide is designed to fit seamlessly into the top frame of the popular Maker Select Plus, as well as its clones, such as the i3 plus.