mount x 3d models

So, I came up with a solution by designing a cover that can replace the original X-Axis limit switch cover. This new cover has enough space to accommodate the LED switch, and it extrudes slightly to ensure that it doesn't make contact with the...

Modification for original X carriage. Mods are: 23 mm holes for hotend cooler (for some reason i have bigger one). 2 mm holes near bottom for stabile printing (i heard that prevents unsticking). Vertical and horizontal holes for servo Z probe. Bigger...

This is a simple adjustable belt tensioner that mounts on the top rod on the right end of the X gantry. See it in action... Instructions For an adjustable tensioner you need to add a 624...

I created these RAM mounts to try to solve a problem; This thing rotates when a phone is mounted. This model is not to be considered to be accurate, but should serve well for any kind of fitment requirements. ... The spring was modeled in the relaxed...

This is a simple adjustable belt tensioner that mounts on the top rod on the right end of the X gantry.See it in action…InstructionsFor an adjustable tensioner you need to add a 624 bearing, a 4mm screw, and a 3mm screw to this part. It's designed...

... arrangement of the stock printed piece. ...I made this one, so as to place the bolt more in line with the endstop, to create more X space. Make sure your X axis can move all the way to the endstop without crashing before homing with this design.

Gopro type mount (check my other designs you will find a pi camera v2 case with go pro mount that works with default lens or m12 mount: https://www.thingiverse.com/thing:4837895) I didn't check clearance with an actual go pro camera, this was made...

This is a remix of the mount by 3D-Maniac that allows for clearance of a side-mounted LCD on the Bear Frame. ...It also includes a remix of Dragsterbox's PiCam vs enclosure to allow for installation of Arducam's version (the SMD's on the rear interfere...

Customized version of https://www.thingiverse.com/thing:4445610 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4445610

Customized version of https://www.thingiverse.com/thing:4445610 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4445610

PlanePrint Big Bobber motor mount to support Alloy Motor mount with 24mm x 24mm hole spacing. Use M3 x 6mm Screws to attach alloy motor mount. ...

This is to make the camera mount compatible with the following X Ends: https://www.thingiverse.com/thing:3559732/files

This is a mount for a 40x40mm fan for cooling (primarily) the X and Y stepper-drivers. ...The mount is made for a Makerbase Gen L board as used by the JGAurora A5.

Simple way to mount tablets. ...I´m using tablets as external displays for X-Plane 11 data. Simply glue the parts together any angle you like using superglue. ...

I used Wings3D to extract the motor mount from jebk's design, then modelled a new base in Fusion360 to attach to the x-carriage, and finally used 3D Builder to combine the two pieces. Also chopped the cable chain mount off the x-carriage, which is...

4] Print 1 X-carriage or modify your favorite X-carriage to add mounts for the fan mounts/duct. 5] Slide the fan mounts into the duct, they should sort of snap in to place. Use some super glue if needed. 6] Insert nuts in the nut locks at the top of...

... any module you want to attached to that. The two mounts I've made here are for the iPhone X in Portrait and the iPad Mini 2 in landscape. There are 2 holes to glue in the magnets for this. ...The magnets needed are 10x3 mm neodymium magnets.

PlanePrint Big Bobber motor mount with 16mm x 16mm hole spacing. Use M3 Screws to attach motor or as recommended from your motor manual. ... Recommend PETG or ABS for strength and motor temp.

Mount most any webcam on the X-Axis motor using a standard tripod 1/4-20 bolt (available at just about any home improvement store.) The Fusion 360 file is also included, if you need to make any adjustments.

This is a cable chain Mount for the Anet A8 Printer. It fits to the x-axis Motor. It can hold chains for the x and z axis . The chain modules included are not my design, but i use them for every chain on my Printer. there is an Adapter included, if...

(Be careful not to pinch the lower x-axis belt when sliding the indicator mount over the rail.) 4. Zero the indicator in the leveled area. 5. Move indicator mount and print bed to level the other three corners. 6. ...Slide mount off rail and you are...

40mm fan mount that replaces the right side X carriage panel on a Prusa i3. Has a hole for X stop screw and a channel for the fan wires. The circular disks on each corner are .5mm additions to reduce the corners from lifting during a print. ...They...

... ... This mount adds tensioners on both sides for the X-axis belt. Uses 2x M3x10mm bolt and 2x M3 nut. Nut goes in underneath, bolt goes in from outside, belt goes under the mount and around the small curved pieces, then can be zip-tied to itself.

# Ender 3 compact mount for E3D Hemera - The aio mount version(recommend) will keep the x offset of nozzle unchange and maximum the X build size is 235mm. This version only use 3 m3x7mm bolts to mount the Hemera to the plate. - You will need to...

(https://www.thingiverse.com/thing:2847987) I had an issue where the left mount arm would hit a screw on the rod mount for the X axis when homing and it wouldn't trip the end-stop. (I blame the "thereish" assembly of the D6 - not the original...

This version only use 3 m3x7mm button head bolts to mount the Hemera to the plate. You will need to change the x build size to 220mm if you are using the "compact" version. 4020 fan mount is based on Joe Casha's design on myminifactory but can be use...

However, unlike a DSLR on a gimbal, a mobile phone doesn't have a hot shoe mount (and neither do most gimbals), so this Thing solves just that giving you the ability to mount your Rode Videomic onto your X-Cam Sight 2 gimbal! You can check my review...

This is the universal spindle mount, found purchasable from the X-Carve website. It works perfectly with their spindle mounting plate. It is designed to go with a 52mm spindle, like the one they sell on their website. You can print either two or...

Designed to work with cheap cable chains available on Amazon: https://www.amazon.co.uk/gp/product/B07WJ4CPF5/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&th=1 As in original design, X mount will snap fit over the spacers for the X carriage Z Mount is...

Die Aufnahme passt auf einen MegaBee Frame von iFlight, ober vergleichbare Copter mit einem Bohrbild (Breite:23mm x Länge: 37mm), weitere Bohrbilder für andere Frames folgen Im Augenblick folgende Winkel verfügbar: 5°, 10°, 15°, 20° TPU-Mount ist so...