msar log in 3d models

I found the artifacts causing the problem and while I was working on the file I found some places to improve. Improved filament path, all internal paths are now exactly 2mm and the profile at each filament input/output is the same profile as the...

Here's the text translated and optimized for SEO in English: Harry Potter Owl Light: A 3D Printed Masterpiece with RGB LED Dive into the magical world of Hogwarts with our exclusive Harry Potter owl light crafted through 3D printing. Inspired by the...

... but DM me with any questions. It's build **parametrically**, so it should be easy to adjust angles/venting/sizes/etc. I was sort of a beginner to Fusion when I made this, so there could be some anomalies or inefficiencies in the file.

- I assembled everything to the main body, by last I inserted the 2 top wheels, holding the carriage in place and finally the belt bracket. * Sequence of the 2 top wheels: M5 x 30mm bolt (or longer), v solid wheels, washer, nylon spacer, main body,...

Solder the cables to the switch and after that glue the switch into the hole.Glue the PCB In-Place  Take the glue gun and put four glue drops on every pillar. Press the cut PCB on the pillars and hold it down for 30 seconds. Then take the...

Changed the Guides so that the Shaft could be removed in one peace. ... Update : 22.06.2022 Added a 21 cm Version and some Longholes for Adjustment 30 x M6 Fastner ...

... Whether you're looking to add some ambiance to a cozy bedroom or create a dramatic focal point in a living room, the Solo Tube Ceiling Lamp is sure to impress. Crafted from high-quality materials, this lamp exudes a sense of luxury and refinement.

... some points fail to adhere to the bed. You can see a lot of the issues in the close-up print photo, but in-person these flaws are much less noticeable. ...I imagine with a .25mm nozzle it would come out much better, but I haven't tried it yet.</p>

In its current design (pun), there is only enough room for the 97% single channel or 95% dual channel. When ordering these units, you can specify the current range. It is highly recommended to use a current rating as close to the amount of amperage...

This project demonstrates a unique integration of technologies such as RFID and interactive displays in fab labs, enhancing user engagement and learning experience. ...By following these steps, makers can create their own ESP32-based LCD cover with...

Parts are created in 3d modeling software, no copyrighted product had been scanned in any way. These models are for personal use as proxies and should never be sold. ...If it causes copyright issues, i will remove it.</p> <p>Remixed from:<br/> <a...

I was introduced to filament riveting in the "Articulated finger extensions" project by JulienJeanRoy https://www.thingiverse.com/thing:4342323 You use a soldering iron or wood working tool, set to the lowest temperature, and melt the end of a piece...

Lesson/Activity Duration: Educators have flexibility in customizing the duration based on the complexity of programming desired. For Kindergartners, it could be as simple as having a sound played when the animal moves, while for 3rd Grade students,...

Furthermore I created the endstop mounts which are already present in the Fusion 360 model. I will try to update the pictures today or tomorrow. Now it gets exiting! Electronics are next! **Update 9** (03.07.2018): After test driving the Z-Axis I...

**What is a cold pull?** A cold pull is when filament that is embedded in the nozzle is pulled out under a low temperature sweet spot so that it completely peels away leaving the nozzle with a clean inner surface. This is good for removing clogs and...

I can not execute this script, as the given text is just a description of different parameters in G-code that are being passed. If you want to create such patterns then I'll be able to assist with finding out how it works and also give suggestions...

... itself to be complete, the FreeCAD file, particularly how dimensions are parameterized, are a bit messy. Consider the FreeCAD file a work in progress, though I may not get around to refactoring it, as it were, unless there is significant interest.

I didn't enable all the features, which are relevant for the Bigtreetech TFT Firmware, because the custom firmware can't be flashed in case of the recently shipped GD32F305 chipset. I also left unsupported hardware features disabled. ##...

If a player rolls a number with an empty slot, they place one of their tokens in the respective slot and their turn is over. If the slot is already occupied by another token, the player takes the token (a virus token for the first uninfected player...

Raspberry Pi Zero and Pi Zero 2 Case Compatible with old &amp; newerPi Zero,Pi Zero 2 &amp;Pi Zero W (includes a camera ribbon slot) Snap fit design -no screws required. Heat sink hole for the 2W variation. "Coin slot" provided to prise lid open....

https://youtu.be/-M99N8JkQxQ IronThrone_SupportFree_icz.stl (Need infill) IronThrone_SupportFree_NoInfill_icz.stl (No infill with sloped seat. Printed in timelapse) Subscribe to find out more support free 4K Time-lapse video: Subscribe...

My wife hated the builder supplied garage window inserts in our house (depicting a sunrise), and wanted instead the Stockton style (grid) inserts. I looked around, nothing in Canada, pretty expensive to order from USA ($305 CAD with shipping and...

I know that the bulb I found off Thingiverse needed a part to hold the LEDs in, so I took to Tinkercad to play around a bit and see what I could come up with. I ended up adding a tube-like structure into the centre of the bulb to house the LEDs as it...

I posted the first part of the project for those interested in this topic. I also shot a video on how to make a spiral twisted brush (It was made of natural bristles and copper wires.). When I finish, I'll post it. Subscribe (Watch) in order not to...

Parts are created in 3d modeling software, no copyrighted product had been scanned in any way. These models are for personal use as proxies and should never be sold. ...If it causes copyright issues, i will remove it.</p> <p>Remixed from:<br/> <a...

I plan to somehow make the handle tilted, to not to loose it while changing filter :) * Added optional sensor (full frame) framing window that can be screwed in after the filter (from camera side). I hoped it will minimise flaring, but seems to not...

... for stability. Adjust the tension in the M5 screws to increase or decrease friction in the moving components. Use appropriate washers and even grease where necessary, or if necessary to ensure the nuts don't unscrew. ...Nylocs help here too.

Working on version 2.0, where comes more types, this will be archived soon. Insulin case This case is primarily made for travelling, but it is handy even in everyday use. It has two sections for insulin pens and one section for 4 pen needles. Case...

If a player rolls a number with an empty slot, they place one of their tokens in the respective slot and their turn is over. If the slot is already occupied by another token, the player takes the token (a virus token for the first uninfected player...

Staunton (Modified) Chess Set&nbsp;The Staunton chess set is composed of a style of chess pieces used in competitions. The journalist Nathaniel Cooke is credited with the design, and they are named after the English chess master Howard Staunton.This...