nested platonic solids 3d models

It is a solid model which, when mounted correctly, does not produce noise or increase the footprint of the printer.Important: The parts of the MK4 version are not compatible with those of the MK3 version (and vice versa)! Due to the new display...

Example code and wiring diagrams are included for both the Arduino Nano and Wemos D1 Mini (ESP8266).Personalise it to your needs by including more hardware, such as thermometers, motion detection, buttons etc or use a Wemos D1 Mini to connect it to...

You will be redirected to 3DHubs website, where you can choose the material you want to print the parts in and the 3D printing service provider.On 26.12.2016 the model files have been optimized and made solid. They now are adapted to be 3D printed...

You will need two solid state relays because you will be using two separate power supplies to power the bed heaters in pairs. Wire the inputs of the relays both to the 12V bed terminals on your Ramps together. So it turns both relays on and off at...

... PLA (1.7653 avg. dia.)Nozzle Diameter - 0.5mmBed Temp - 50 DegreesExtruder Temp. - 210 Deg.Retraction - 4mmExtrusion Multiplier - 1.01Layer Height - 0.02mmTop / Bottom Solid Layers - 1mmFill Density - 30%Infill Type - TrianglesRaft / Support - None

4 perimeters is basically solid. Notes: With Simplify3D I printed the first part to 4.6mm, snapped in the ring, then finished the print. Your settings may work better with a different number. Basically I did it at the point where there were only 2...

I'm gluing all the parts on shaft one to make this more solid with the metal hanger in the center. I'm also gluing the ends of shaft two, end one and end two, because if you don't, there will be enough play for middle gear to skip. Additionally,...

I did find that, even with me printing solid, some filaments were more brittle than others. For the most part there weren’t too many issue, but the heads of some bolts occasionally snapped off. Unfortunately, the horizontal layer line are the...

As I fixed those on the other models, I just used solid shapes as fill. On this one, I added a couple holes along the vertical separator for the cargo. This felt like a nice touch, but again, worried about printability, so I added a stylistic beam...

The Frame was light and durable at this time but not solid enough (to much vibration) so in my next real version (V4 to this time) I did increase the arms dimension and overworked the connection in middle. This version was a huge improvement but...

The estop pin should have at least three shells to make it solid since it shouldn't be exposed to any sideways pressure. It can work just fine with no infill or you can be extra careful and use 100% infill - either way, it doesn't matter much...

PrintingI recommend printing from PETG, the model is designed for 0.2mm layer height and three perimeters.Activate “solid infill threshold” and set 15mm^2 value - this is to fill up small areas around the suspension mount screws.The motor mount...

The mask has been designed for you to be able to take the Dome on and off, which locks in place with a solid 6 pin system, so it won't rattle around and mounts snug onto the face mask. The facemask has small cut outs on the side and under the mouth...

**Pictures** - [phone_holder_demo.png] : this picture shows the computed phone holder in open scad - [phone_holder_demo_front+split.png] : this picture shows the computed phone holder in open scad with splited parts - [phone_holder_demo_back.png] :...

Also, I've had good success printing this at 0% infill, and the piece still feels very solid. The goal of this mask is to make a respirator that's stupid simple to print/operate (no supports, rims or rafts needed) and uses a readily...

Attach the A mount to your goggles and slide the quick slots into each other.Replace Goggles X LED front cover:Remove the top part of the face foam to reveal two small screw holesUse a PH0/J0 philips screwdriver to remove the two screwsUse a...

They did require a little clean up but they are still pretty solid and cleaned up well enough. The fit onto the existing x-axis cover was just the right amount of snug. Props to Cavac for a well done design. I printed using PLA+ (just what I...

The "monochrome" version is especially easy to print; just print six copies of `coffin.starlight.solid.stl`. (You can, of course, print the copies in different colors, and you might get an interesting color pattern out of it; but the colors won't...

You'll need to use epoxy or some solid glue to seal the back. Since I didn't have a microswitch at the time, I used a 3-pin jumper to select LED/Buzzer vs vibrator. Also, you can cover the battery tubes with some soft materials so that it feels more...

À compléter avec : 6 vis à bois ou metal (diamètre 4mm ou inférieur), pour la fixation du support au mur 3 vis (diamètre 4mm ou inférieur, longueur 25 à 40mm) et 3 écrous, pour les tiges de maintient (part C) 4 roulements à billes 8x16x5 (diamètre...

###The Middle Two Sections: Because I wanted to model the Arch in a high level of detail, but also wanted to be able to fit it in a sane amount of space, I had to come to a compromise -- I would model the solid shape of the entire arch at 1:1200...

It uses OpenTK so it should be fast * Zoom in to see individual segments, and choose Solid, Layers, or Rainbow color coding of segments * See the whole 3D object, or by layer, or by line segment(s). If you select by layer or segments, the...

Just make sure they are scaled evenly.The files are the tree with no holes (if you just want the tree), the tree with all the proper holes and a solid bottom, a tree with all the holes and NO bottom (for a light bulb stand, just google Industrial...

Then only the area of ​​the vertical axis is printed solid. A 0.3 mm nozzle would be recommended for the rotor blade, I printed with 0.4 mm. On the Nabe, drill out the holes for the screws with 2.5 mm and cut an M3 thread. Glue the Labyrinth ring to...

The transition from the infill to the top solid layers is rather hard for the printer because of the many interruptions in the diagonal due to the hex bit holes. So the print needs several layers to recover a smooth surface.</p><p>I recommend 15%...

Using a solid metal cylinder might work better. Depending on the installation details, putting too much force on the filter housing could conceivably damage your plumbing, so be careful! THIS WRENCH SHOULD BE USED TO *REMOVE* THE FILTER...

... into 2 files. * Increased solid space on divider cards to make more room for hand-writing custom dividers without the need to create new geometry. ... Update 2018-10-10: Added card dividers to separate stacks when storing game away mid-session.

The tricky part here is to make sure that you completely fill in each of the colors for a solid design. There are a couple of tricks I employ here to make this work:</p> <ul> <li>Slightly increase your extrusion multiplier, which will ensure that the...

As an experiment, I'm thinking of getting hold of a set of the tiny rice-grain lights, the ones with the tiny solid wires. I think these would make it possible to fit far more lights into the space, without the wires spoiling the overall effect. ...

Grabowski’s collection includes: vessels (for liquid medicines), vases, jars (including albarella) and tins (for semi-liquid and solid medicines). The names of the preparations, most often in Latin, were typically placed in cartouches painted on the...