nintendo 64 raspberry pi 4 3d models

Hello Guys, My first model here is for a Raspberry PI4 with a PIFI DAC+ 2.0 installed. This setup is perfect for any audio project you have in mind and utilizes this particular dac effectively. I am still learning how to model, so tolerances may not...

I made a small case the same size as the circuit board of raspberry pi4. You can install a heat sink and a 40x40x10mm or 30x30x7mm fan. I am fixing the case with 2Mx8mm screws. Please enjoy! Print Settings Printer Brand: Creality Printer: Ender 3...

Has a nice fit and you can easily slide your Pi in and out after installing it to your wall. I printed the version with the cutouts but I've added another one without them for easier printing without supports. ...Print in standard model orientation...

Installed WPSD fork of Pi-Star. Hint: To update the firmware you need to solder jumper JP1. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: Low Quality (0.28mm) Infill: 20% Filament: Generic PLA ...

I installed the light-bar to be controlled via relay and my Pi, so I added some space internal to case to house this relay. [Relay is an Adafruit P4409, link also below]. This case version can also support an internal fan as well as heat sink, which...

A simple wall mount for my raspi 4 and sata drive. ... Print with supports

... under the shim screw to act as spacer! Also, I tested with the original raspberry foundation HDMI cables. This case works nicely with these cables. I included the original Top for convenience, should you not need my new Top Design. ... Have fun!

This safe setup holds it away from the plate edges, preventing vibration wear and neatly routing the cable to the rear of the Taz where I have my Pi installed. Print flat on the plate with any filament you prefer but I suggest using high-temperature...

I can't say if these vents do much to help with airflow and cooling because the Pi does sit very close to the bottom of the case and fits pretty tightly around the edges. So, that will impede the potential of these vents. The majority of intake air...

This is a remix of Sparrows89's Gamecube Pi Classic and TheJeffChen's Logo Dunk Corner Stand.I've previously remixed this case for the RPI3B and decided that I wanted to make it for my RPI4B, too - and while remodeling it to fit the 4B, I also fixed...

This is a remix of Sparrows89's Gamecube Pi Classic ( https://www.myminifactory.com/object/3d-print-gamecube-pi-classic-45314 ) and TheJeffChen's Logo Dunk Corner Stand. I've previously remixed this case for the RPI3B and decided that I wanted to...

I quickly edited my previous design for RPI 4 Original model is here : https://www.thingiverse.com/thing:4579831

a slim mount with multiple mounting points for RPI 3 or 4 *4, m3-.50 x 10 bolts *4, m3-.50 nuts Nuts just press in by hand. ...very easy mounting holes are 4mm wide to mount bracket to wall or whatever you desire.

A duct routes the wires to the Pi GPIO pins for connection up. I only use +5 and Gnd, but anyone wanting PWM control or RPM monitoring should consider the GPIO voltage limits. This clip-on clamps pretty tight and only makes things a little bigger. I...

Only four M3x10 screws - done.I printed it in PETG with little support in the overhangs (holes for the rivet nuts), which are really easy to remove.One Note:To mount the Pi I had to enlarge the holes by 0,5mm. I simply tapped through the existing...

... to fit on top of the MKS 1.4 board and will require 20mm longer screws for secure mounting. To assemble, you will need the following parts: * 4x Longer screws than your previous MKS Gen 1.4 mount * 4x M2.5 bolts * 4x M2.5 nuts (nyloc or regular)

Camera mount for GHOST 4 printer for Astroprint or Octoprint. ...Print original files from https://www.thingiverse.com/thing:2113975 without I3_MK2_Camera_Mount_straight.stl and these files instead.

I had to find a solution to securely attach my Raspi-4 to its armor case heatsink. ...The fit was snug, far from ideal, but this approach worked adequately for my purposes in building a NAS enclosure.

Remix of Malolo's RPi 4 case * base plate with tabs for a 75mm Vesa mount * top from 40mm fan opening with screw mounts, extended height 2mm, added GPIO cutout

#Gridfinity RaspberryPi 4 Holder Stores 3 x RaspbverryPi4 in a 2x2 grid Fusion360 File included to mix sizes to your own requirements. ... Other models Check out my other models https://www.printables.com/@Micah_754861

It is a simple and easy to print case for RPi 4 with a capability to install a 40x40x10mm fan, which is just snapped onto the top part of the case. GPIO slot can be covered with a simple insert, that partially hides the cable mess. Only screws,...

this is a minor remix of BaudlerArtDesign's Rpi 4 case found here : https://www.thingiverse.com/thing:1815268 This resdesign was made to help with exhaust airflow slightly, along with adding rail mounts to the bottom shell to mount it on the left...

Remix of the incredible RPi 4 Case from Plammers. Upgraded version released on June 30, 2019, specifically designed to accommodate the original HDMI cable. Crafted for a secure one-hole mount on VESA 200 Mount using an M6x12 screw. The mounting...

Camera Mount Upgrade for GHOST 4 Printer Users with Astroprint or Octoprint. ...Get Ready to Print Original Files Directly from Thingiverse at https://www.thingiverse.com/thing:2113975, But Don't Forget to Download I3_MK2_Camera_Mount_straight.stl and...

This versatile combo cabinet is designed to house both MKS 1.4 and RPI for Octoprint, making it an all-in-one solution for your 3D printing needs. Please note that cables must be attached before inserting the MKS board into the front panel. ...The build...

... You can access the detailed instructions here: https://www.instructables.com/id/4CH-Relay-board-Controlled-With-Push-Buttons/. The custom case I've designed is specifically for mounting the RPI 3B+ and the 4-channel relay board together efficiently.

This comprehensive all-in-one combo cabinet seamlessly integrates MKS 1.4 and RPI for Octoprint functionality. Important Note: Before inserting the MKS board inside, please ensure cables are securely attached. Key Features: * Print upside down...

Remix for a RPi 4 with a GPIO 3.5 cheap screen. I'm printing this for now but working on a remix of this with a 30mm cooler and better color filament :P I modified also the slot for the board because it was too tight. Edit: Added another version...

Remix for a RPi 4 with a GPIO 3.5 cheap screen. I'm printing this for now but working on a remix of this with a 30mm cooler and better color filament :P I modified also the slot for the board because it was too tight. Edit: Added another...

Top case for RPI3 and Keyestudio 4 relay hat: I've designed it to be expandable, just like the Mykorhiza model, with four holes to accommodate LED indicators for each relay. Spacer between RPI and relay hat. Top fullfill.stl - this design is...