nooelec ham it up 3d models
1550872 3d models found related to nooelec ham it up.thingiverse
This is a case for the NooElec Ham It Up Upconverter for SDR radios (http://www.nooelec.com/store/software-defined-radio/sdr-accessories/ham-it-up-v1-0-rf-upconverter-for-software-defined-radio.html#.UjJ60sbbN8E) OpenSCAD file included. ... Wrapping it...
thingiverse
This is a cover for the nooelec ham it up upconverter if your version has no holes for the noise source. You just need to connect the two enable (EN) pins together and add a sma port. This cover should fit most sma plugs that are on the same height...
thingiverse
Made with FreeCAD This is a simple case consisting of 2 parts for your Ham It Up v1.3 Upconverter SDR by NooElec. It has enough air, tolerance and tiniest ventilation holes in case you run it 24/7 and in the desert. :D It just fits without any screws...
thingiverse
Deckel mit 2 Schrauben oder Tropfen Kleber befestigen. ...Ich habe etwas Tesafilm genommen.
thingiverse
Created this because the other ones that others have made had dimensions that were slightly smaller than the actual board. Very basic, but helps protect the board. ...Should work without modifications.
thingiverse
This is a tight fitting case for my Ham-It-Up board. Shown in the picture is one half of the case. The idea is to put the halves together and use copper tape to hold it together and offer shielding. There's a pin hole in the side to see the power...
thingiverse
***UPDATED*** Just a simple mount to hang my HamItUp on the pegboard next to my HackRF. ...I have replaced the V2 files with V3 fort structural concerns. I also recommend printing this on its side.
thingiverse
... screw holes to the bottom to close it securely. Printed at .2 layer height. Case for the Ham it up v1.3: http://www.nooelec.com/store/ham-it-up.html I didn't want to spend for the aluminum case, so I built my own. ...This is my first CAD model.
thingiverse
... Mendel with a 0.4 nozzle. ... Using write.scad from https://www.thingiverse.com/thing:16193 You Better Wrap it up, B! ... Components: Arduino Nano WTV020 Red Arcade Button 3x Red LED 3x 220ohm resistor 8ohm 0.25w Speaker DC Jack Veroboard
thingiverse
I generated this stl to honor those lighting it up for Autism Awareness Day. You can modify this file to work as a night light cover. ... http://www.lightitupblue.org
prusaprinters
Solder wires to the magnets Now the LEDs and wires are in place and it is time to attach the magnets that will be used to connect the two pieces and simultaneously conduct the electricity, turning the lamp on. When magnets get too hot they can lose...
cults3d
Modeling of a hook to support different things. ...I used it for pot lids to make it better if found in the kitchen area. ... I modified the file from the photo to strengthen the grip.
thingiverse
I needed a new plug for the bathtub and it's some ridiculously useless size so hopefully this will work and I can have a bath that doesn't drain because of an ill fitting plug!
3docean
Ham 3d model in cartoon style. Preview images are rendered in Vray. ... .max 2014 .FBX .OBJ 2048×2048 JPG textures 752 poly 832 vert In subdivision Level 0
thingiverse
A miniature of the first generation Pump it Up cabinet, i left a hole where the screen is for inserting a light/screen. Also the dance mats can be lid up if printed with the top piece. ...Parts need to be glued together.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=518217 Instructions Using the following options: box_depth = 40 box_high = 40 raised = 0 message = it might sober me up box_wall_thickness = 3 font_size = 15 box_width = 50 Font =...
thingiverse
The F'ed Up Sword is made in Fusion 360, which I am a whole lot more familiar with, but I still need to be occasionally reminded that it's okay to f*** things up there. Might make a spacecraft next, because that's the main thing besides swords...
3docean
It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) - *.obj (Multi Format) - *.3ds (Multi...
thingiverse
Will follow up with a shot of the actual printed part. ... Print Settings Printer Brand: MakerBot Printer: MakerBot...
thingiverse
... a one of a kind light holder that can move using gears and a handle. You can spin it as fast or as slow as you want and it illuminates anything from a dark room to the night sky. Also it works as a great conversation starter. ...I hope you like it!
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/ggBjshhX8Sp
grabcad
Gripper for Ring it up challenge, holds up to 2 rings at a time