nozzle cam 3d models

So inspired by [this design]( https://www.thingiverse.com/thing:4859502) and the way it use the pi-cam, I made an small arm that can be attached to [this blokhead version](https://www.thingiverse.com/thing:4777217). So It's easier to see the first...

So inspired by this design and the way it use the pi-cam, I made an small arm that can be attached to this blokhead version. So It's easier to see the first layer. It needs: 2 M1.7x8mm screws for attaching pi camera. and 2 M3x5 for the articulation...

CR10-S Nozzle cam Angled 15 degrees so it can focus on the tip of the nozzle

Nozzle Cam for the CR10S Pro V2 - It should fit on anything that has the same fan shroud. ... Camera module itself can be found here https://www.aliexpress.com/item/32832909804.html

This remix adds a holder for a 7mm or 8mm USB endoscope as nozzle-cam (only tested with a 7mm since the 8mm has not arrived yet). The holder points the endoscope at the tip of the nozzle. Make sure the endoscope has a short focal length since it...

... which recessed into the body. If the screw is too long it can interfere with the frame. Warning: nozzle-cams can be very mesmerizing, I take no responsibility for hours wasted watching it XD. Otherwise like the normal one. Category: 3D Printer Parts

Been playing with the Nozzle cam. Made a super simple mod to the fan shroud that allowed me to use a $22 Otoscope camera. I will come up with some added light to keep the exposure time shorter to get better motion images but it’s really useful in...

Universal nozzle cam should be able to be used with any aftermarket fan duct that has a 40 mm fan open for easy access such as the hero me or the one I'm using Satsana 5015. I would recommend using a higher temperature resistant filament such as...

that way I can watch whats going on with my print from the luxury of my couch =) I have attached a fusion 360 file of the entire project if you care to make any modifications STP file of the unified nozzle cam fan shroud STL of the unified nozzle...

This is an ESP32 cam nozzle camera ad on for Bowden X-Carriage Mount for E3D V6 from Thingiverse. It is simple to print and assemble.</p><p>&nbsp;</p><p><strong>Assembly</strong></p><ol><li>Print all the parts.</li><li>If your camera module has focus...

I basically blended these too things together to get a nozzle cam that fits 8mm usb borescopes from amazon. ... I used a few M3 screws and nuts to secure it and it is fully adjustable!

Turn out it is actually 7.3mm and I had to try a few different scales to get it to fit perfectly, so I am uploading 3 sizes because your 7mm camera is probably a little off too. nozzle_cam_7mm.stl - the file I used nozzle_cam_7mm_small.stl -a little...

Parts used for this nozzle cam project: - Fantronics USB Endoscope: https://amzn.to/3t76jVb - Blips Macro Plus Lens: https://amzn.to/3r9EkTb - 30 Gauge Silicone wires: https://amzn.to/3r4a9wr - 5050 LEDs (24v): https://amzn.to/3aiiBSc - 5050 LEDs...

// Easy to customize nozzle cam for Biqu B1( the hole on the camera mount is 8 mm) // You can modify the angle of the camera and you can also move it closer. You will need: 4 x M4 screws (3x about 1cm long and 1x 2,2 cm long)( you don't have to...

I made this to mount a 5.5mm endoscope on to my extruder and make a nozzle cam controlled by Raspberry Pi and Octoprint. This rear mounted design is the easiest to install and has the best cable management. Basically it just adds another zip-tie...

// Easy to customize nozzle cam for Biqu B1( the hole on the camera mount is 8 mm) //You can modify the angle of the camera and you can also move it closer.You will need:4 x M4 screws (3x about 1cm long and 1x 2,2 cm long)( you don't have to be very...

I also added a nozzle cam which can hold a 8mm (diameter) usb endoscope camera. If you don't want the camera, there is also a version without camera holder. __NOTE:__ After mounting it to the printer it is necessary to relevel the bed!!! I...

I also added a nozzle cam which can hold a 8mm (diameter) usb endoscope camera. If you don't want the camera, there is also a version without camera holder. NOTE: After mounting it to the printer it is necessary to relevel the bed!!! I tested it...

This is a bracket to mount and endoscope camera on the print head of a Geeetech A30 to allow the deposition of the plastic to be closely monitored during the print.

Print with Support. ... Also check out the Video how to build your Nozzle Cam: https://youtu.be/Jg_AKzuWCMw

Just print with support. ... I recommend printing with PETG or ABS in any case. Nozzle Cam how to can be found there: https://youtu.be/Jg_AKzuWCMw Focus the lense to about 20mm, but u can adjust the cam anyway

Did a really quick mash up of 'Sidewinder X1 - extruder flat cable clamp V2' (https://www.thingiverse.com/thing:3945539) and 'CR-10s Nozzle cam' holder (https://www.thingiverse.com/thing:3450281). ...

a quick release nozzle cam designed for the hero me light weight ducts and the night vision pi cameras available on amazon and other retailers. this provides excellent vision of the nozzle and keeps the dual 5015 blower fans secured more tightly, no...

Some cheap cameras like mine has a better focus when the camera is away from nozzle.Check movement in all axis (nothing crashes??).Do a Fist Layer Calibration Check out my Github: https://github.com/andimoto/prusa-mini-nozzle-camI also added SCAD...

- Do a Fist Layer Calibration Check out my Github: https://github.com/andimoto/prusa-mini-nozzle-cam I also added SCAD File if someone wants do do some change. This is the 1st usable version. I have some ideas, I will implement to get a better...

- Do a Fist Layer Calibration Check out my Github: https://github.com/andimoto/prusa-mini-nozzle-cam I also added SCAD File if someone wants do do some change. This is the 1st usable version. I have some ideas, I will implement to get a better...

Just remove the old fan shroud and relpace it with this one.I also added a nozzle cam which can hold a 8mm (diameter) usb endoscope camera.If you don't want the camera, there is also a version without camera holder.NOTE: After mounting it to the...

Made for 5.5mm Endoscope camera. ... I used PLA, but it would be healthier to use PETG or ABS.

KEEP AN EYE out for updates to the design. I've created a mount for a PI V2 camera to allow monitoring of my prints close up. ... This system also uses generative design for a very organic looking shape

I printed it with das Filament PETG with no Problems.It is Important to use PETG or even more Temp resistant material, because the camera heats up threw the heatbet and threw itsself.If you want to use an cam with a smaller diameter just print...