octoprint ender 3 pro 3d models
822103 3d models found related to octoprint ender 3 pro.thingiverse
... like the following tutorial (I still use a Raspberry Pi). https://www.youtube.com/watch?v=74xdib_-X38 Print Settings Printer brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 20% Filament material: PLA
thingiverse
This is a housing for Raspberry Pi 2/3 that's fits to the V-Rails of Creality Ender 3 (pro) I printed two of the tee-bars and then glued them, with a gap in between, to the larger part of the RPI case with CA glue. (Print the T-bars upright, no...
thingiverse
Raspberry Pi 3B behind Monitor Mount With 40mm Fan Mount I changed the Fans of my Ender 3 Pro. Hotend 2x 12v (one for Mainboard 1 for Hotend serial) Coolingfan 2x (one for Raspberry one for Print cooling) Make sure your printer is correct setup....
thingiverse
This is an integrated enclosure for the Raspberry Pi 4B, specifically for users running Octoprint on their Ender 3 or Ender 3 Pro (Read note at bottom). I am particularly proud of this design because of the elegant and simple approach I took when...
thingiverse
... this box from Scott Yu-jan. ...I really liked his video's but I used a raspberry pi 3. His model was made for the raspberry pi 4. But its really clever to put some buck converters in there. ...So i replaced the part where the raspberry pi 4 is placed.
thingiverse
Mounts for the Ender 3, Ender 3 Pro, Teva Tornado and more: ================================================= I also added 3 new mounts, one that works with 4040 extrusions, and two others that will work with 2020 extrusions. + ...
thingiverse
This version will fit an Ender 3 Pro and hold larger FC-65 high-amp relays and larger LM2596 voltage regulator with LCD display, in addition to the smaller form factor LM2596. The same XT60 connectors, fan, and screw sizes are used as in the...
cults3d
This version will fit an Ender 3 Pro and hold larger FC-65 high-amp relays and larger LM2596 voltage regulator with LCD display, in addition to the smaller form factor LM2596. The same XT60 connectors, fan, and screw sizes are used as in the...
thingiverse
Case for Raspberry Pi which is designed exactly for the back of the Ender 3 Pro. I use a Raspberry Pi 3 Model B with the latest version of octoprint. With the plugin "enclosure" the two relays can be controlled. Parts: Raspberry Pi 3 LM2596 DC-DC...
thingiverse
I design this to use an old smartphone as a display to control octoprint
thingiverse
Remixed the original design to fit a raspberry pi 4 and 2 buck converters! Also removed the logo on the cover too. This is designed for a 30mm fan. ...I got this cheap one from eBay: https://ebay.us/iBLdfj Video of this thing in action: ...
thingiverse
New handle for the Crealty Ender 3 S1 pro for mounting a Pi Zero W 2 with camera and OctoPrint.
thingiverse
This design was inspired by [giacomo30196](https://www.thingiverse.com/giacomo30196)'s beautiful [AiO Ender 3 Octoprint Set Up](https://www.thingiverse.com/thing:3063845) design, but completely made from scratch for Ender 3 Pro and Raspberry Pi 3...
thingiverse
This design is a remix of my [Raspberry Pi 3 Model A+ case](https://www.thingiverse.com/thing:3338152) for the Raspberry Pi Model B+: It adds a case to your Ender 3 (Pro) that fits a Raspberry Pi 3 Model B+, a 10A relay (for switching LEDs on/off),...
thingiverse
... und mit dem Slicer in die Öffnungen des Deckels gemacht. ... Die Cam-Halterung habe ich von https://www.thingiverse.com/thing:3147295 Unter https://technikmensch.de/octoprint/ habe ich eine super Anleitung gefunden. ...
thingiverse
I'm using the Octoprint-Enclosure plug in to trigger some GCODE for each button. As buttons, I used some generic 24mm "arcade buttons" found on amazon. I use the top 6 buttons to perform routine actions, homing, set temperatures, filament...
thingiverse
This is a 3-part case designed to mount a Raspberry Pi 3B+ to a Creality Ender 3 using M3 machine screws and t-nuts. Mounting points in the center part allow for the installation of a small 5V fan for cooling the pi during use. This fan may be...
thingiverse
Antenna mount goes into the Enders case cover hole that initialy was made for Z endstop cable. Dmall thingie C6 that is for saving the camera cable from skew. It should be pressed in the hole where camera ribon slides into the camera box. OPI...
prusaprinters
The cover portion fits nicely within the frame and can be removed whenever you want to.This is a remix of “Octoprint Monitor Single Station Front Cover” by Bazzelworks found at this link Octoprint Monitor Single Station Front Cover by...
thingiverse
I've remade this to fit the Ender 3 Max as it is made differently and the original one just doesn't fit it. This is made to slot into the 4020 section ad located behind the installed LCD screen. ...and hole for 40mm fan is in the side to allow air...
thingiverse
Therefore I designed a angle-arm which attaches nicely to the initial mount and camera case. The two pieces are held together with a single M3 screw + nut. For any information about what you'll need for the base mount check out the original...
thingiverse
A Raspberry Pi Zero case that fits the Ender 3 for monitoring with Octoprint.
thingiverse
... the driver bouard is HX711. These STL is what I made for my 3D printing cabinet. The spool holder is from my Creality Ender 3 Pro, but I use it for my Prusa as well. ... Info on the plugin: https://plugins.octoprint.org/plugins/filament_scale/
thingiverse
Case to mount a 16x2 LCD on an Ender 3 V2 I use it in conjunction with the LCD1602 I2c display (0.1.0) plugin on my Octoprint server Mounts nice and neat above the factory display Feel free to use/ modify
thingiverse
English A case for the Raspberry Pi to get the most out of Octoprint, with short cable runs this case adapts perfectly to the Ender 3 v2, as if it was already designed that way at purchase. </p> <p>The 24V power supply line can be laid directly in...
thingiverse
Add **custom shortcut buttons** to your Ender 3 using Octoprint and the [Physical Button Plugin](https://plugins.octoprint.org/plugins/physicalbutton/)! Now you can simply heat your hotend or bed with just one click. I've assigned the buttons to...
prusaprinters
Check the Thingiverse page here to see previous makes and remixes. SEE ALSO:Universal Buttonbox (for example for enclosures or other printers) Ender-3 ButtonBox (for OctoPrint)This is for the people who prefer to use Ctrl+S over jumping...
thingiverse
# Ender-3 ButtonBox (for OctoPrint) # This is for the people who prefer to use Ctrl+S over jumping into menus to save something. On my Ender-3 I got tired of scrolling through the LCD menu to use basic functions like homing all axes, preheating for...
thingiverse
Just a simple clip on case for the Ender 3 X gantry to house my Octoprint Monitor. I just wanted a quick way to check on my print status without needing to approach the printer to open the LCD cover I have on it & kept misplacing the Octoprint...
thingiverse
This is an OctoPrint case for a Raspberry Pi 3B to be attached to the front extruder rail of a Creality Ender 3. This is a remix/meld of the Raspberry Pi 2/3 case by jayftee and the camera mount by StokedGiraffe. Many thanks to these folks for the...