oculus quest 2 3d modeling

I have trouble getting my fingers between the strap on my Oculus Quest 2 and the end of my 90* USBc charging cord, so I made this little slip on that makes it from barely possible to only kinda hard. This was designed to fit the Aceyoon cable, may...

BOM: - 4x M3x8mm Screws - 2x M3x12mm (up to 25mm) Screws - 4x M3 Nuts - 2x M3 Low Profile Nyloc Nuts (Prusa builders might have spares) - 1x M2x8mm Screw - 1x M2x12mm Screw - 1x M2x12mm Standoff - 1x Pen Spring OR 3mm of Silicone Hose with ID of 3mm...

I modified cable clips for the quest 2, so they go on the headstrap, which ensures that the pulleys I have pull on the center of the headset, and not the side

This STL may save your strapless headset from sitting in the dust for the rest of eternity. ...Follow the instructions and in half an hour your Quest 2 will be good as new

Just a small cable clip for a generic 3m link-cable so it wobbles less on the Quest 2. Diameter of the cable is 5,6mm. ...Official Link-cable may be different.

This is a remix of the great Quest 2 adapters that SolidRye designed for the inexpensive Sony MDR-ZX110 headphones. ...I made them about 8mm wider on each side for larger heads.

This holds an Anker PowerCore10000 power bank onto the collection of Elite Strap clones here for the Oculus Quest 2. I found other solutions for holding the power bank too hard to use. I didn't have any good rubber bands, and wasn't about to waste a...

This is a remix of hadtstec's rift headphone adapters from here: https://www.thingiverse.com/thing:3652427 This has been modded to fit securely on the Quest 2 since it uses a totally different strap design. These headphones are great if you're...

The simple solution is to not use it plugged in, but then the cable hangs down and irritates when you wear the Quest 2. ... So the simple solution is a new cable guard, where the cable is routed better and the last guard doubles as a holder for the...

Original design by 10P6 and I thank you much for that :) I have a Quest 2.... I have a 3d printer.... but its only a 120mmx120mmx120mm build volume, Monoprice Select Mini v2 e3d. i altered the bottom piece on the length only to fit the 120mm. Then...

Clip for Chinostrap Oculus Link Cable Remix of ---> https://www.thingiverse.com/thing:4629345

Anker PD 10000 Powerbank holder for Quest 2 elite strap. For counterweight and extended battery life. If there are comfort issues from the mounts please use some padding on the back of the strap Tested on Elite Battery strap. ...But it should work...

... Mark the top of the lens before removing it from the frame. ...If necessary, secure with instant adhesive against rotation. The glasses should be ordered with 65mm IPD for quest 2. ...

Its just a Remix from this https://www.thingiverse.com/thing:4631187?part=001cc735-c1a3-4abe-9acf-0a9c7e4e7ea0  for the Quest 2 Bobovr M1 Plus Headstrap.

Oculus Quest VIVE Audio Headset Adapter

Simple clip for the Quest 2 standard headstraps. Works with the Newzerol and Anker Link cables. New version included for the Original Link cable with a smaller diameter as its cable is thinner. Has a second clip on the outside for...

I haven't been able to find a universal battery pack holder for the Ozero Quest 2 elite strap so I decided to draw one up. This is designed to use velcro style cable straps to hold the holder to the head strap and small zip ties to hold the pack to...

Simple clip for the Quest 2 standard headstraps. Works with the Newzerol and Anker Link cables. New version included for the Original Link cable with a smaller diameter as its cable is thinner. Has a second clip on the outside for...

This is an easily-printed clip-on battery pack holder for the Quest 2 Elite Strap. Just print, slot the pieces together (perhaps with a little bit of glue), add some foam, and you're good to go. STEP assembly included so you can create your own...

I wanted to create a Power Bank Clamp system for my Quest 2 BOBOVR M2 Strap to act as a counterbalance for the front heavy VR headset and at the same time utilise the power bank to extend the available playtime. I tweaked the design to achieve both.

Makes it more convenient and realistic to use a two-handed weapon in VR with the Quest 2. I got tired of my hands constantly moving around whilst sword fighting. I handle swords IRL, and this annoyed me, so I made this. I can't remember where online...

This fixes an issue I had where there was very little plastic between the inset nut holder and the outside of the model causing it to be weak. I also thickened the pieces attaching the cylinder to the main model by 1mm. I made the clip extend 1mm...

This fixes an issue I had where there was very little plastic between the inset nut holder and the outside of the model causing it to be weak. I also thickened the pieces attaching the cylinder to the main model by 1mm. I made the clip extend 1mm...

Quest 2 Golf+ adapter. Just add 1 or 2 velcro straps. I found the best success with the "CUSTOM" club in the golf+ settings and aligning the remote onscreen with the actual location of the remote on the golf club handle in real life. The dead eye...

Remixed to properly fit original Oculus link cable. Easier to put on. Sturdier too. ... Thanks to AbeFM https://www.thingiverse.com/thing:4711712/files for original design.

**This is an easily-printed clip-on battery pack holder for the Quest 2 Elite Strap**. Just print, slot the pieces together (perhaps with a little bit of glue), add some foam, and you're good to go. **STEP assembly included so you can create your...

Remix of the [Quest 2 wall mount made by lensfort](https://www.thingiverse.com/thing:4630669). I noticed that the HMD mount started to sag over time, so I chose to add some support beams to it and decided that I might as well upload it here. If you...

Neat gunstock for FPS games on the Oculus 2. After printing three of these for friends I decided to improve a few issues I found and greatly simplify the process for others. Most of the source models have disparate and confusing instructions, so I...

Sanlaki's Quest 2 VR non-dominant controller mount gave me a lot of wrist problems and that's likely because the non-dominant hand is mounted like the dominant hand as if there are two pistol grips but a foregrip or a handguard position is nothing at...

Was gonna grab some of the Sony ZX110 headphones for my Quest 2 and realized i had an old pair of Skull Candy over ear headphones that I remember rivaling my $200 bose set. So I remixed SolidRye's mount to use the cut up skull candy units. Give a...