old computer models

Update 03_2020: Some issue corrections in 3D models for slicing with Cura. Added a body for a 9V battery. Update 04_2020: Added a flap for PET (Apollinaris or Schweppes brand). For those who wonder which bottles this was built for; I forgot to...

The solution is simple enough: Both parts of the model need to be placed away from the centre point (still properly lined up with one another, obviously), so that the probe can do its thing without the first print getting in the way. So began...

For smaller sizes, the cost may not drop enough to justify not buying an off-the-shelf model. This project is intended for larger format printers and those who want to learn how 3D printers are built and work. This project is not for the faint of...

The picture of my working bitx40 model does not have the SPEAKER MIC wired up yet -still waiting for 2.5mm stereo jack. Files and features are subject to CHANGE. I will attempt to post relevant details with revision bumps as they occur. Also,...

The Hull is designed to be printed by any experience level and the assembly should also be able to be finished with little experience in 3D printing or modeling. Tools: -Hobby Knife -CA Glue -Hand Drill + Drill Index -Sandpaper (80 Grit) Good Luck...

https://www.youtube.com/watch?v=Nn9B46IjsVU ______________________________________________________ ENGLISH ______________________________________________________ Only tested on T12-X, but can work on equivalent models with boxes of the same...

These are modelled from the original Type-R parts. (I reinforced these as much as possible). What you need? - Complete RB6 rear mount transmission and motor mount. (Transmission case that comes with the spare part set numbered UM508C.) - About...

Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20% Notes: I've printed the model with a 0.2mm layer height (to print it very fast) and I've just done an infill of 20%, but it will bend a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_shape = 3 custom_right_port_length = 30 stencil_drawing =...

(Note: If you don’t care about the enclosure being air-tight, you don’t need the straight pieces!) ### Printing the parts The STL folder contains rendered models for a 24"x24" box with 0.118" / 3.0mm acrylic, but the scad files are easily adapted for...

This model drops excess wind The concept is to use it quietly This mod may be a bit more difficult 5015-24v fan 5015-12v or 24v fan * Please note that the polarity of the fan electrodes may be reversed. DC-DC adjustable step-down power supply I...

DescriptionThis is a fast and easy to print model to calibrate your new filament. It can be used to find the right settings for the extrusion factor to get the right wall thickness.</p><p>It is designed with a 0.86 mm wall thickness to meet the...

If you need to use a different pump you can model and print your own adapter as it is just a rectangle block with a hole for the pump water outlet. The inlet block should be 80mm tall and 32mm wide minus half a millimeter for fit tolerance. If you...

It should be possible to customise the model by changing a global variables that represent the battery dimension and straps width- holes for the LED indicators- reducing the number of screws- creating the cases for wider range of IMUsPlease let me...

It's a character they can indefinitly model and remix. The great Charles Chaplin was all of that and much more. And Thelmo adores him. So having an OTTO Chaplin now makes perfect sense. Thelmo could have found with many other inspirations for his...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Reference photos http://ww2german.com/flu1694.html Reference data https://archive.org/details/Tm9-1901/page/n89/mode/2up https://bulletpicker.com/pdf/TM%209-1300-203,%20Artillery%20Ammunition.pdf#page=262 You can edit this model here...

These parameters were guided by experience and where I felt strength was merited as well as Prusa's investigations into watertight printing. I used regular PLA and after the print I briefly blasted the prints with a heat gun. Make sure not to have...

Note: Scaling down the model too small may not work on all printers. The smaller the part, the more precise your printer should be. 1/2 scale should work well without extra precision. Any smaller will need a printer which supports a step of .05 mm...

Update: -Ive added a FDM "optimised" file, as the other model did not have a perfectly even bottom which would have made probelms when printing the first layer on an FDM printer. -Ive updated the schematic and eliminated a mistake. -Ive added...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

The shade is 196mm high - be sure it fits your printer's build volume. Print it in white or even translucent PLA. The model has been adjusted in Meshmixer to be solid. You need to print this in <strong>Spiral Vase Mode</strong>! This will print the...

It was created by taking the NIH approved visor and flattened with patterning software and modeled tabs so that it can be added to the Prusa 4-hole layout. The removable visor can be 3D printed or laser cut for maximum efficiency.</p> <p>I have tried...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

This fits in a 35mm (1 3/8") hole that you should drill in the rear-center of the unit Instructions My pipe had an OD of 60.5mm and I rounded up to 61 in the model. It's a great fit and I've included the SCAD file if you need to modify this diameter....

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the horizontality...

I designed this model so the unused limit switch from my CR-10 Mini can be easily repurposed as a filament runout sensor. The limit switch is commonly found in Creality CR-10 and Ender 3 printers and consists of an SPDT switch mounted on a small PCB...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame which require support. You may need to use a raft or brim to secure the part...

A lot of the model are just perimeters or solid bottom/top layers. The pass-through holes for the cables create small bridges first and they are closed first, and then the top cover is printed. ...So I made a few arrangements to allow decent printing...