oogie boogie 3d model

... mount and two each side for accessory mounts. I used one on the right for strain relief for E3D wires, 2 on left for fan mount. 4 on side fan, only two are used depending on fan model. ...2 on cable chain attachment to attach it to extruder mount.

However another person created this and the subsequent prusaslicer ini file. however I am not quite knowledgeable enough with gcode and prusaslicer to make the necessary adjustments to it to make it work on the mini (plus I prefer to do it directly...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_radius = 6 custom_top_port_corner_radius = 5 custom_back_extra_port_y_position = 30 pattern_line_thickness = 20...

Trim/Cut plastic flowers from a dollar store. Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to...

Rollerspooler is the latest in TUSH-Varientalology, using the base Idea from the original The Ultimate Spool Holder (by filamentry) then adding the Clamp from the original Prusa Spool Holder (because, why reinvent a perfectly working wheel?) to mount...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

The engraving starts at 1.8mm and the model continues at 2.2mm. Use contrasting colors for a clear reading. <b>note:</b> <i>* If you suffer from corner bulge / swell or an elephant’s foot after printing, carefully sand / deburr them. When...

Post-Printing // model: Prusa i3 MK3 Y Chassis Bearing Straps // This replaces the zip ties that tend to stretch and can reduce accuracy over time. Optionally, also replace the entire strap and bearing with a 1-piece printed version that has been...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

Print Settings: - Printer Brand: RepRap - Printer Model: Prusa i3 - Rafts: No - Resolution: 0.2mm - Infill: 30% Notes: 1st Part to Print: "Bottom Mount" This part doesn't require any support material. It's the most complex print in this design,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

and Pause Layer = 2. How I Designed This Print on Window Screen This model was designed to have the printer paused at ~1mm to have the screen inserted. I made sure I made the frame thick enough to allow for multiple layers to be printed on each side...

I probably should make that easier to do if when printing the full model instead of the slices (maybe an exercise for the one wanting to do that - add a better wire hole). I used a 2.1 bluetooth stereo board that I got on ebay for about $21...

For any other question, please feel free to reach out, or leave a comment. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .2mm Infill: 20% Filament: Jarees PETG Matte Black Notes: Support is only...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside. These are for sink and drain plumbing only,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

But the base design is a mix of: Ichibey's Sakura CoreCube Hbot modeling work Jetguy's lasercutter templates and electrical / extruder configuration DNewman's Sailfish programming for CoreXY gantries Credit should go to the above -- I'm just...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

All overhangs should be 45 degrees or less. Rafts: Not required, unless you experience adhesion issues. License The "Hard Drive Holder" models (.stl) are licensed under the CC BY license by Code and Make. The "Hard Drive Holder" code (.scad) is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 7 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

In this case, I have proven that it is valid for several models of Epson projectors, which are the ones I like the most, seriously, I hate dlp projectors. They tire my eyes a lot and all of them, to a greater or lesser extent, create a rainbow...

... control the LEDS with preset printer events such as warming, printing progress, error, cooling, etc. https://plugins.octoprint.org/plugins/wled/ Original design remixed from K2DesignLab: https://www.printables.com/model/174959-makerdeck-logo

I RECOMMEND THIS ONE INSTEAD:https://www.printables.com/model/169138-prusa-mini-detachable-cooling-duct-assembly-v2 About this modI have never been happy (okay that's a lie, I was happy for the first few weeks) with my Prusa Mini's cooling. This is...