over extruding first layer 3d models

It's very frustrating.&nbsp;The Einsy base now has a very thin extension for mounting the fan with the layer lines running in the wrong direction. It can be very brittle. be careful or you'll break it as I did. super glue fixed it.&nbsp;</p><p>I...

Each layer of feathers come with a separate controller. Each feather also comes with a separate controller. And more... Animation Unlooped eating animation at 30 fps, frame range 0-200 Tag hummingbird, bird, flowers, small, wings, animals, fly,...

A 3D printed ‘box’, designed as separate box sides that bolt/screw together, to not only make printing easier, but also to allow the sensor and ESP32 components to be easily assembled inside the ‘box’.The ‘bolting together’ is accomplished by...

Then, change your support overhang settings to add supports to anything more than the angle before it. Text Quality Test: Adjust print speed, quality, infill, layer height, etc. ...settings until the model prints cleanly.</p> </div></p></p></p> ...

The aim of the SRT is to enable you to work in a more ergonomic position.Whether you're slim, fat, puny or muscular will also affect your support points and influence your needs.The aim of the SRT is to be able to adapt the inclination to improve...

Why didn't you use a smaller design? To make this reliably printable on a wide variety of FDM machines, it was important to ensure that the contact area on the print bed was large, there are minimal overhangs and that it does not require high...

Print settings: Use six shells and a twelve percent infill, and print at .31-millimeter layer height if you can. Print the model as is for the Front piece and MIRROR the part Z axis for the Back part. Position the part on its back with the legs...

GEOMETRY * Scene configuration consists of collapsing stacked levels into single level files reducing polycount numbers while improving render times by up to several thousand frames • Multiple hierarchical grouping enabled - allows models for...

80% infill, 1 shell, .2mm layer height, using Ryobi green(ish) ABS is recommended for aesthetic pleasure, thermal resistance and overall part longevity. Once it cools, clean up the few strands of plastic from lack of supports, and pop it on your...

You want to make sure your 3D printer machine bed is level and also calibrated.I print most of the time with a raft, especially for the PIN.0.4 Nozzle size0.2 layer height207 Nozzle temp (don't know why, but sometimes I fail with 200C)75C Initial bed...

Objects are logically arranged within an intuitive layering system - for optimal accessibility and streamlined productivity. In light of transparency, it should be mentioned that we're only providing the asset itself - without including the...

Test fit it with enough layers of foam to make sure of it! You dont want the Deck to move around and damage the display with the Thumbsticks!!Attach the clips before you glue the TPU bumpers to the edges of the case, otherwise you will have a hard...

Max scene organized by layers with precise naming for all objects, materials and textures for effortless integration. Available in Single object format with multiple export options: - Game Ready (.uasset & .fbx) - perfect for seamless importing...

I use 3 walls, 30% grid infill and a 0.24mm layer height. I've also checked the options "alternate extra wall" and "infill before walls" in cura</p> I would suggest printing the frame in either PLA, PLA+ or ABS. PLA is the stiffest of the 3, but...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

Print directions: ► Material: PLA+ ► Layer height: 0.3mm ► Support: Only on build plate, do not support bridges. These options are important to make the detent feature work correctly! Assembly: Just remove the supports and attach the PETG face sheet....

... to a 5mm shaft. Print Settings Printer Brand: LulzBot Printer: TAZ 5 Rafts: No Supports: No Resolution: 0.5Mm nozzle 0.35mm layers Infill: 85% or better Notes: I printed this unit in ABS, but PLA or other material would work just as well here.

&nbsp;I did them in PETG but I think PLA should work fine.I did 0.24 layer height and 5% infill with PETG. &nbsp;The key is flexibilty so you can get it on and off. &nbsp;You can change the thickness of the clip with the variables if you want...

My design has two strain relief clips that replace the original ones:The holder fits very well in the case:And here you can see my PCB mounted:PrintingI have printed the pcb mount using PETG in variable layer height (0.12…0.3mm). The design is...

Layer 0.2mm is okay. No supports. No rafts. No brim. V1 arm is fine too, but there's a risk of collision with some models of the head in very rare cases of high and wide prints. Prepare all parts. Power off the printer. Unplug the power cable! Make...

You can print these shells as individual layers that are glued together.Extra Magnet - Glue a 3x3mm cylinder magnet into the metal dowel pin hole in the base so that the pin is held in place until the puzzle is given a slap. Make sure the magnet is...

If a specific CRS is essential, ask before you pay Any scene size or crop to an area-of-interest — for best performance and format compatibility, inquire before paying Buildings, land-use areas, roads and railways split by type — layers / named...

If a specific CRS is essential, ask before you pay Any scene size or crop to an area-of-interest — for best performance and format compatibility, inquire before paying Buildings, land-use areas, roads and railways split by type — layers / named...

Filleted fronts weren't ideal for pulling chits out because chits would snag on layers. -HPXP -- Arms now point straight up. ...Angled arms weren't pointing at obvious wheel face.</p> <p>-- Wheel was sunken into base to give better lid clearance when in...

The utensil part of this device is detachable to allow for easier cleaning.&nbsp;Tools:- Snips, dremel, or an angle grinder (to cut the steel fork)- Needle nose pliers (to remove supports)Print Instructions:- 100% infill- 0.2mm layer height- yes...

Furthermore, the material plates are freely selectable no matter whether wood, plastic aluminum or (plexi) glass Depending on the plate material I would then adjust the infil in order to get enough stability, I printed the test pattern with the...

Unfortunately, there's not enough adhesion between the layers to screw the cylinder and lid together, so you'll have to glue them. Or use brackets and a M2 .5x8 screw.The version supplied is for a right-hand door. The left-hand version will come...

The straight risers are made of solid oak boards, while the curved ones are made of multiple layers of poplar, rough-cut and glued together, then drum sanded to shape. In retrospect, I'd probably use something other than poplar, as it's not very...

The lower section was printed with its opening facing upward, without support, and with additional top layers added to the raft for a smoother outer appearance. Launch Controller Internal Electrical Hardware: The brass electrical hardware is...

I used ABS for outdoor durability, but any material will work. If deploying outdoors, you'll want to make sure that your infill and layer adhesion are set so the enclosure has no way for moisture ingress. ...To help with this, there is an optional...