paintball gopro mount 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_rod_nut_od = 8.05 gopro_bar_screw_d = 4 gopro_ext_len = 45 gopro_captive_rod_angle = 45 gopro_ext_th = 3 gopro_bar_th = 3.2...

GoPro mount designed for paintball enthusiasts who want to view a new angle of their game. This mount slides right onto the barrel of a 21" diameter paintball barrel. Tighten it with a nut and bolt and you are ready to go! ... *Exclusive sponsored gift...

I changed some dimensions from @Jody_T 's design to get more stable mount for GoPro 8 for VForce Paintball goggles. Also included place for nut in order to secure camera to the mount. You need to put M5 nut in the hole, which is tight enough so you...

I changed some dimensions from @Jody_T 's design to get more stable mount for GoPro 8 for VForce Paintball goggles. Also included place for nut in order to secure camera to the mount. You need to put M5 nut in the hole, which is tight enough so you...

Snug fit to a Empire EVS Paintball Mask, Just needs a zip tie through the vent to secure in place, I couldn't find anywhere to clip the mount without a ziptie. ... Made mine with 85% infill

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_primary = triple gopro_secondary_what = clamp gopro_captive_protruding_h = 0.5 gopro_bar_th = 5.0 gopro_bar_gap = 2.4...

For use on a standard paintball 7/8 inch or 1 inch barrel. For best results use a piece of rubber between for more stability. Video soon. Works best when tilted on the side with a 90 deg extension. ... Need 2 x M3x20 or so and 2 x M3 nuts.

I've only tested it with Eflex's, but you can make it work with most masks without any serious changes.

This is ah gopro mount for my paintball marker. The inner diameter is 21mm. ... You need two m2 screw, nuts and a m6 screw to mount it

gopro paintball barrel mount for 21mm barrel (outer diameter) this is made a little over sized to make room for Self Amalgamating Tape (rubber tape) or any other grippy tape. ... hardware: M5x30 bolt and a M5 nylon locking nut

Standard: https://goo.gl/R53wW8 Deluxe/Heavy Duty: https://goo.gl/zWsUaS Etsy Shop: https://goo.gl/VmLxyi Version 1 is a GoPro Barrel Mount for a tipmann A5 though it will probably work on the 98 and X7 as well. Leave a comment if you need a...

Rear mount gopro case: Fits HERO Session 5 and was remixed to fit with the mount I created. The mounting holes line up really tight and I had to thread the bolt in. I used an M5 bolt and nut here. Use an M3 screw and nut to tighten the case. I...

Sturdy GoPro mount for your dye i4 paintball mask. You will need two 1/8in nuts and bolts to put this together, as well as the nut and bolt from an existing GoPro mount. ...How I Designed This SolidWorks 2014

The **MNT-P** is a low profile Action Cam mount designed for the ** PUSH UNITE ** Paintball mask (but may fit various others), ***that doesn't damage the fins of your mask and provides an even lower connection point than any other Mount on the...

EASY TO PRINT and NO EXTRA TOOLS NEEDS This is a mount I use to attach my GoPro camera to my paintball gun's barrel. The barrel has (outside) diameter 22mm (0.86inch). The mount is design the way you do not need any support while printing - that's...

The hardware i used to mount this on my mask was EVERBILT nylon lock nuts (M5-0.8mm) which is used to mount the gopro case, EVERBILT socket cap screws metric plain (m4.5x35mm) which you use to hold the gopro mount itself in place, and EVERBILT...

An action cam base for Empire EVS paintball mask. Needs some modification before installing such as cutting the ribs on bottom of the plate and drilling larger holes if needed. Credits to uploader jc61990 (thing 470945). ...The top part was reused...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I use this mount for the video: https://youtu.be/Up__XNtx1Sg (insert like this http://www.dx.com/es/p/jtron-m3-copper-flower-screw-nut-die-cast-screw-nut-mosaic-screw-nut-100-pcs-283956#.VS9_ySHtmko) Actualization!!! ...The files are the same but...

These mounts are used to hang your paintball masks on the wall. The regular file should work for most masks except the Dye I5. ... The I5 will need the xl mound due to the bulkier strap.

Here is a paintball marker wall mount I came up with. The peg has a hole in it for a 10/32x1" bolt and nut. ... This is to strengthen the peg and prevent a marker from hitting the floor on the off chance the peg breaks.

Wall mounted holder/hanger for your paintball markers.Wall mounted screws are hidden behind the pegs for looks.I printed in PETG using 4 walls for strength and to reduce the chance of delamination in the portion that the pegs are slotted...

This is a reversion of http://www.thingiverse.com/thing:13724 universal contour camera mount that I modified to be mounted on my paintball gun barrel, I used two 1" 6-32 screws and nuts to hold it to the barrel that i had left from my printrbot LC, I...

... you have one. I took CG/weight comparisons with all markers I could find and came to this particular angle/mount position and depth to work with 99% of setups out there. ... I've got 4 markers wall mounted with this already, and holding up great!

Suporte Para Câmera Gopro Máscara Airsoft PaintballI

... ... And Because i lost allready 2 gopros (one lost, one smashed) i combined a riser with a protective housing for the gopro THe riser is Special for mounting on AR-15. ... i added a second plan in with a normal rail mount plate for any picatinny rail

This mount is designed to go onto any picatinny rail of paintball guns or airsoft alike. Capable of mounting slings and other accessories that use an S Clip. For best results print the body on its side with supports to hold up the loop. ...Print with...

This paintball marker setup wall mount was designed with the intention of being both simple and easy to use.Simply print both pieces out of high-quality PLA and then do the following:Mount the large tank holder to the wall using drywall anchors (use...

Update: February 5, 2017 Improved description Add STEP files Update: November 25 2019 Added a DYE-I5 Mount Update: October 8 2016 Add a left and right ver with no holes on the opposite side. This was for those who could mirror the part in there...

Suporte Para Cano E Câmera Gopro Airsoft Paintball