pcb plotter

FamiCoun - Famicom Front Expansion for NES & SNES Controller
prusaprinters

You may want to plug in a controller into the printed plug first, insert the pins in from the back of the printed piece, one port at a time, then fit the PCB over the stumps and solder. Use just enough amount of the solder. Make sure nothing...

Star Trek Next Generation Tricorder - TR-580 v1 (arduino)
prusaprinters

 After gluing, cut them flush.All custom PCB files are on github, and custom board(s) can be ordered via EasyEDA or OSHPark.Code for the sense board is also on github:https://github.com/lambtor/ArduinoTricorderHardware used, shown in one of the...

Motorized blinds extremely cheap (IKEA Fridans esphome HA Home Assistant , MQTT homekit/homebridge + more or standalone)
thingiverse

> I orderd some PCB from an online PCB-Maker, to keep it tidy, but works just as well with "protoboard". > 2 x 20mm long m3 screws and nuts (preferably one 25/30mm m3 screw to fixate the nuts, see included photos) > 1 x 28byj-48 5v stepper...

Maple Mini Pin Protector
thingiverse

These can be used for adding a tiny 7x2 or 7x3 hole piece of prototype PCB in order to add additional ground and 3.3V pins at the top end of the module, and optionally even two additional LEDs that can be externally connected to any desired output...

BIQU H2 complete Kit for B1 dual 4010 Fan - V1
thingiverse

so did a lot of work redesigning the mount, extended it to fit the 4010 fan between extruder and hotend PCB and also changed the mount position so that the nozzle is as close as possible centered from the carriage, else i guess you cant use the full...

BTT Mini 12864 RGB Enclosure
thingiverse

Do not excessively press the reset button on the front panel until the screen pcb is installed and fixed (screwed) correctly; risk of the reset button breaking. **Important Notes: This enclosure can be compatible with Mini 12864 RGB LCD screens...

3D-Printed Circuit Board v0.2
myminifactory

currently limited by width of slide switch -- get_component_distance() = 13.5 Contribute For the most up to date code, or to contribute directly to the project, https://github.com/CarryTheWhat/3D-PCB To contribute indirectly, visit...

Combined Gotek and CF-ide in 3.5" disk drive
prusaprinters

I have a Gotek drive and CF-IDE card reader for my Amiga 4000.As I already use the 5,25” bay for a CD-ROM drive, and one of the 3,5” bay’s for the original Floppy drive, I needed another solution.My A4000 has a standard height floppy drive, so there...

Silent Wall and Desk Clock
thingiverse

Basically you want to cut a single PCB trace (check with multimeter afterwards that the trace is cut) https://ardufocus.com/howto/28byj-48-bipolar-hw-mod/ You can remove the end of the cable with the connector, we don't need it, as well as the red...

Hercules - QIDI X-Plus / I-Mate (S) Carriage for BMG & Dragon / E3D V6
thingiverse

Here's a comparison picture by Hercules user techguychad: What to print: Print these files: hercules-1.7.2.stl hercules-dial-holder-1.3.stl hercules-belt-peg-1.2.stl hercules-fan-duct-1.3.stl bmg-handle-short-1.0.stl...

Hercules - QIDI X-Max Carriage for BMG & Dragon / E3D V6
thingiverse

Here's a comparison picture by Hercules user techguychad: What to print: Print these files: hercules-1.7.2.stl hercules-dial-holder-1.3.stl hercules-belt-peg-1.2.stl hercules-fan-duct-1.3.stl bmg-handle-short-1.0.stl...

Hitbox - Arcade Stick
prusaprinters

I have wanted to upload it to the site, but have postponed it several times due to the complexity and amount of work required to make it upload worthy.So who is this case for? If you are like me and have made custom arcade sticks before and have...