phone lens adapter 3d models

Customized version of http://www.thingiverse.com/thing:2568474 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2568474

Customized version of http://www.thingiverse.com/thing:2568474 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2568474

Customized version of https://www.thingiverse.com/thing:2568474 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2568474

This is a concept design that is meant to be coupled with any lens i.e a microscope lens, to record work, the piece "corredera_lente" can be edited to fit the geometry of your lens.

This is a concept design for a phone holder that can be coupled with any lens.Files can be downloaded it here:https://a360.co/3dCcWriThread in piece "corredera_lente" has a designation M20x 1.5 6H

This is a clip for adapting a lens to a cell phone, turning it into a microscope. The model was adapted from the Pacific Northwest National Laboratory (https://www.thingiverse.com/thing:667471). The main difference is that this model uses a lens...

This is a clip for adapting a lens to a cell phone, turning it into a microscope. The model was adapted from the Pacific Northwest National Laboratory (https://www.thingiverse.com/thing:667471). The main difference is that this model uses a lens...

Lens adapter better with two rings

... lenses left over. And since they are to big for my GoPro Hero 4, I made an adapter. It's for lenses with an outside measurement of 51 millimeters and rather tight. ... So I did a little bit of 'Dremel-work' and pressed it carefully into place.

GoPro Lens adapter

... and I prefer my other case design. For anyone who wants to making this design, the binocular male adapters on my other adapter design works with this one. More information on my website (https://www.souzoumaker.com/blog-1/2017/8/8/lens-adapter)

lens adapter for naked gopro , and filter support

Adapter that connects phones to Slit Lamp Device.

This adapter is for reversing a lens with 52 mm filter thread. Suitable for Pentax cameras. ... Reversing the lens allows to do closeup macro photography.

This is a lens adapter for GoPro Hero3. ... It uses Kenko "27S MC C-UP NO3 silver" close up lens, and adjust focus to near point than normal.

Ysaron 240mm tube lens adapter M42. ...You need 42mm-52mm step-down and step-up lens filter adapters from ebay. Press them in using epoxy/superglue etc. ...I used Weld-On #16.

I create this lens adapter for this VR Headset : http://www.thingiverse.com/thing:729029 It allow to 25mm lens (Google Cardboard) instead of 38mm It was created with Blender, the sources files are in the download category

This adapter can be used to mount a Pentaflex lens to a MFT camera. So far I haven't come across a lens that actually covers the entire sensor. MFT was entirely designed with metal in mind so the bayonet tabs are probably way too flimsy to support...

I solved this problem by creating a new back end for the Moondog Anamorphic lens which houses the magnet behind the metal plate that the lever presses down to clamp to the phone. The magnet I use is a rather standard 10x3mm magnet that I found...

This is a lens adapter that allows inexpensive Zenni round lenses to be mounted to an HP Reverb VR headset. The adapter MUST MUST MUST be printed in stretch TPU. TPU allows this to stretch over the headset lens mounts. If it don't stretch, it don't...

So I designed an adapter ring that clips into where the lens filter would screw in. Her lens is a 35-80mm and fits 52mm filters. The hood I printed and designed this for is webboggles' Canon EF-S 17-85 lens hood (thing 73161). ...There is also a...

This is a adapter I've made to be able to capture very cool macro photos with insane magnification (like 3:1 with a 28mm lens) with my current lens. ... Now you can 3D Print a Reverse Ring instead of buying one!

There is also an adapter ring stack for the Wide lens to use with the Tele if you don't want to use two separate systems or buy two step up rings. Update: The new 58mm tele is the same diameter as the wide, so you no longer need two adapters! I...

Simple 12mm to 18mm adapter for laser cutter.Improves stability by using 18mm groove in lens holder.Print with TPU outer wall first, no expansion needed already accounted for in designe. 

Adapter made for C170 for the following lens: https://www.amazon.com/gp/product/B01FFOFTEM/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 Made this as I was only able to find an adapter for the c270. Hole for lens was sanded a little and then the lens...

I haven't tried modifying the adapter for a smaller filter than lens, so YMMV if you try that... The design is mostly parametric, so if you use OnShape you can copy it to your account and make a version that meets your lens and filter dimensions by...

The adapter clamps around the lens body and then can be threaded into a tripod mount. Note that the model does not contain the threading itself, as we've found that threading the hole using a tap works better. Future work would be to allow for...

It's composed of two separate parts: the base screws on the laser itself and the cover screws on the base, holding any 3,75cm diameter lens. Concave cavity for lens assures that it is perfectly centered. Perfect for thin-film interference...

... head has a cutout slot for a 18mm lens. This adapter will fit the lens snug into the slot. I used 2.6mm Plexi to cut this out, and the fit was perfect. ... Uploaded is the .SVG if you want to edit it yourself, and the .LYZ file for LaserDRW

This Mobius to Zenit lens adapter is intended to serve as a 'long range' microscope, or tele-photo lens. By long range microscope, it is possible to get high magnification, while leaving enough space beneath for working. Note that it is printed with...